Models > DBXR453GV1AA

DBXR453GV1AA General Electric Dryer - Overview

Get Parts and Repair Help for DBXR453GV1AA

If you know the dryer repair part you need, you can browse the list of all parts on the DBXR453GV1AA, or you can search by name or part description. You can also find your part by where it is located on the DBXR453GV1AA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DBXR453GV1AA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.94

Drum Bearing Slide

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 4 hrs and your part ships today!
$6.05

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 4 hrs and your part ships today!
$5.62

Duct Felt Seal

Order within the next 4 hrs and your part ships today!
$21.23

Drive Belt

This drive belt is 89.5" long.

Order within the next 4 hrs and your part ships today!
$7.75

Selector Knob with Clip

This knob accepts a D-shaped shaft. Sold individually.

Order within the next 4 hrs and your part ships today!
$48.46

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

Order within the next 4 hrs and your part ships today!
$34.19

Lint Filter and Frame

Order within the next 4 hrs and your part ships today!
$35.66

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

Order within the next 4 hrs and your part ships today!
$16.50

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 4 hrs and your part ships today!
$36.09

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 520 of 533 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Replaced broken START knob on dryer.

  • Customer: SAM from ROCK HILL NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 471 of 476 people found this instruction helpful
Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.<... read more

Intermittant squeaking noise

  • Customer: Mark from Addison IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 430 of 505 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more