Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DBXR453EV0WW > Instructions

DBXR453EV0WW General Electric Dryer - Instructions

All installation instructions for DBXR453EV0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DBXR453EV0WW
76-90 of 601
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dried something with a plastic coating-

  • Customer: MARY from AUGUSTA, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 22 people found this instruction helpful
Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Dryer starts squeaking while operating

  • Customer: David from Littleton, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Open the dryer door and remove the two screws in the top of the door opening that hold the top of the dryer on, and then remove the dryer top. On the inside of the dryer, there are two screws that hold the front of the dryer on. Remove one screw from each side of the dryer near the top, and the front of the dryer will fall away. The drum slides are visible when you lean the front panel of the dryer out away from the drum. You can replace the drum slides without even removing the front of the dryer completely. Pull out the old drum slides and insert the new slides. Lift the drum slighly from the inside through the dryer door as you tilt the front back into place. Reinsert the screws holding the front of the dryer on and tighten. BE CAREFUL not to drop the screws or you may have to disassemble the dryer to get at the dropped screws. Reinstall the top of the dryer. It is a difficult fit which requres inserting into 3 tabs and sliding the top into place. Check that the top is flush before inserting and tightening the screws in the top of the door opening.

broken knob,and damage rotary start switch

  • Customer: Rosa from miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
replace both,in less than 5 minutes.save 80dollars in labor

Timer Knob slipping and could not set dryer

  • Customer: Rocio from Coconut Creek, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
Searched dryer model on Google, found partselect.com. Searched for Dryer model and a diagram of the dryer with all its parts appeared. Selected the timer knob on the diagram and it took me to the part, ordered it.
All steps took less than 10 minutes, and I had the new knob in my hands the next day and installed in about 3 minutes.
You saved a few dollars, plus not having to miss time from work waiting for a repair man.
Thank you!
Rocio

Loud noise when using dryer

  • Customer: George from Peabody, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
To quiet the noise temporarly I would spray silicone into the dryer drum groove on the front inside panel.Got tired of this and removed the top of the dryer by removing two screws under the front bottom of the dryer top. Remove two screws, one on each side of front panel(screws are on the inside). Lift the front panel straight up and swing to the side. Keep the wires connected to the panel. There is plenty of room to move panel about. Note: I replaced the drum bearing thinking it was a one piece unit with the teflon rub strips. All I had to do is order the teflon rub strips and I would have saved 24 dollars. Reverse the disassembly process to assemble.

Squeaking Dryer!

  • Customer: Marty from El Cerrito, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
A quick look inside verified that the drum slides were worn through but I also found that the plastic drum bearing that holds the slides was cracked in a couple different places. Ordered a new drum bearing, new slides, and decided to replace the felt seal as well since it looked pretty ratty. Parts arrived quickly after ordering and installation literally took 15-20 minutes. Purrs like a baby now. Steps: Unplug dryer. remove two screws which hold top of dryer to front. Remove two screws which hold front (door) to rest of unit. No need to disconnect wiring to front door, just make sure not to pull the wires out! Install new parts. Put it back together in reverse order.

Noisy

  • Customer: Teresa from Brighton, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 7 of 10 people found this instruction helpful
Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.

The start knob would not work

  • Customer: vincent from chapel hill, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
First of all I am NOT a do-it-yourself handyman. I unscrewed the panel where the start knob was diagnosed I needed an electrical switch that went behind the panel and a new start knob. PartSelect was great. just plugged in my model number, found the drawings of the model. I selected and ordered both parts for $40. Shipped normal delivery and they arrived in 5 days. I had the parts replaced, the panel screwed back on and the dryer working in 10 minutes. I highly recommend PartSelect for honesty, speed and helpful drawings that allow you to select the correct part. 110% satisfied.

Intermittent starting gave way to no starting

  • Customer: Carl from Newburgh, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
a. researched internet to find how to access rotary starter switch
b. isolated all electrical input at breaker box
c. removed 4 torx screws on top of dryer head
d. lowered dryer head (swivels toward front)
e. pulled electrical connections from back of switch
f. turned and pulled thus releasing rotary switch
g. reversed procedure above
h. reconnected electrical
i. started dryer - it worked first time
j. watched football until wife came home
k. told wife dryer was fixed and what a bear it was to get it done :o)
l. that night accepted my reward for working so hard at fixing the dryer and saving us a bundle. :o)
m. now we are both smiling

Front drum seal and top drum sliders

  • Customer: Harold from Mingo Junction, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Remove front by removing two screws at top of door opening. Remove front of dryer carefully becsuse of electrical connections for door switch. Drum sliders simply silde in slots at top. (4 are required for total replacement) Door seal simply fits in the groove and locks over end tab. NOTE Do not run dryer any more than absolutelty nessary without lower seal in place.

Old lint filter was cracked from use

  • Customer: Frank from Jacksonville, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 15 people found this instruction helpful
Ordered new lint filter, received it in 2 days, removed old filter, snapped in new filter, patted myself on the back .

Loud squeak at regular intervals

  • Customer: Brian from Bossier City, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
First, I removed the 2 screws for the top panel, lifted the top panel off, then I removed the 2 screws holding the front panel, tilted it forward to clear the drum, disconnected the door switch and set the panel aside. I then installed the 4 slides on the new front bearing, removed the light socket from the old bearing, removed and discarded the old bearing. I installed the light socket into the new bearing and the bearing assembly snapped into place on the front panel. I then re-connected the door switch, aligned the front panel with the drum, secured the front panel with 2 screws, then carefully placed the top panel back in place and secured it with 2 screws. I checked the rotation of the drum and it worked like a champ. Matter of fact, that same day I put this dryer and a matching washer up for sale at 8:30 am on October 31st and by 9:20 am I already sold them!! I delivered and hooked them up and the dryer works great!!!

Dryer becoming increasing noisy and vibrating

  • Customer: Thomas from Long Beach, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 6 of 10 people found this instruction helpful
First remove top cabinet panel by removing two small screws under door recess; then swing up lid and remove from hinged area at the rear. Once top panel is removed, remove the front panel and door assembly by removing two attach screws securing front panel to dryer cabinet. Swing the front panel down and remove from two base hinge points. Slightly lift the front of the dryer drum and wedge some rolled up newspaper between drum and frame to provide access to get your hands through to the idler pulley and motor area. Remove the belt form the motor & idler pulley; then slide the drum out of the cabinet to gain access to the idler pulley. Remove nut securing idler pulley from bracket and remove and replace with new part. Reverse the process to complete the installation.

old bearing completley gone; shaft eating through race making a horrible noise when running

  • Customer: greg from abilene, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

My dryer was especially noisy like a constant squeeking sound.

  • Customer: Mark from Yorkville, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.
Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,

The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business
All Instructions for the DBXR453EV0WW
76-90 of 601