DBSR453EB2WW General Electric Dryer - Instructions

I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.

First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing, take note of the the wireing placement. Replace disc and reverse order of disassembly.

This job was easy for me as I am a tinkerer by nature. The hardest part of the whole job was waiting on the part, which by the way was ordered on a Sunday evening and I had the replacement in my hands and back in the dryer running by 1:00 PM on the following Tuesday!

I book marked this website and WILL refer it to others who simply need a repair, not a costly new appliance!

Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal.

Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3” long).
Removed built-up lint, wiped down area for new duct.
Snapped new duct on.
Dryer works like new!!
Took about 35 minutes, most of time spent cleaning up inside of dryer from lint due to broken duct.

One problem was that salesperson sold me on a new felt strip to go with new duct. That felt comes already installed on the new duct so I did not need it. Cost me a few extra dollars I did not need to spend.

Other than that, easy ordering, fast shipment, and parts are as close to original as possible.

Thanks for all your help!

Very easy. I just snapped the new timer knob on and I was ready to go.

First I really had to hunt for the proper way to get my dryer drum accessible for the repair. With my model it was as simple as removing two screws to take off the top panel (located by opening the dryer door), and then removing two other screws inside the front panel at the top. The front will then be able to swing to the left side (the door switch wires are on this side for this model). Simply remove the drum bearing by gently pulling it off. My slides were in such poor shape for less than 4 years old!! One of them had completely disintegrated! These slides have a small whole on one end which attaches to a small nub at the edge of a slot while the other side just slid into a slot at the other end. No need to even take out the drum!!
The hardest part of the job was to get into the dryer!

I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly.

Just removed the screws at the top of the control panel cover and flipped it down. The switch was then in plain view and simply slid out ( after taking off knob)..placed wire terminals on new switch as I took them off old switch. Slid new switch back in place to lock it in then put control panel cover back into place and replaced screws. Your good to go.

I took apart the top of the dryer and removed the switch and replaced it with the new one. I also removed the knobs and replaced them. Easy

The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a power fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.

pulled out door striker anddoor latch out with pliers and just pushed in new parts. works like new in under a min.

Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires, again vaccumed out lint, lifter drum evough to replace belt. Reassembled

Easy repair. Removed top of dryer and removed two screws to front panel and door assembly. Old front air duct assembly was worn and broken, so it literally fell off the panel. I cleaned the front panel and door assembly of all the lint and dirt, and snapped the new parts into place. The new parts came with the gasket and felt drum seal already installed, to all that had to be done was to snap it into place. Installing the drum slides was a breeze. I simply had to slide one end in the slot, position the hole over the pin, and slide the other end in. I put everything back together, and ran a full cycle for test. Dryer works like new, and run quiet.

I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.

1. removed two screws to take off top.
2. removed two screws to take off front.
3. Took belt off pulley and removed drum.
4. inspected old heating element at back of dryer - saw broken wire
5. replaced heating element (round w/ heating coil)
6. Re-assembled dryer

Helpful hints:
1. mark down or take pictures of all wires before removal - easy to mix them up
2. when you re-attach drum-belt, it should be taught. Comes straight down wall around metal pulley and then forms an "S" as it wraps around plastic pulley on way up. To re-attach, stick both arms into dryer - one to pull plastic-pulley and other to attach belt.