DBLR333GE1WW General Electric Dryer - Instructions

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

Followed instructions from a GE video on how to repair the dryer. The repair was easy and the instructions excellent. The front drum bearing was badly worn, which is reasonable given its age.

Replaced lower drum seal and upper (front) drum bearing

We thought the timer was out on the dryer so I was looking for a new timer when I came across a video on your site about replacing a broken timer knob, so I decided to check the knob first and sure enough it was cracked. This video saved me a lot of time and money. Shipment was quick. Thanks.

PartSelect's troubleshooting page allowed me to quickly diagnose the problem as a worn drum bearing and/or bearing slides. How-to videos made it look so easy I ordered parts (as well as a new drive belt and felt that I figured I'd change while the dryer was open). Two days later the parts were delivered, I got a screw driver out, and dove in. Four screws and 25 minutes later the dryer was running quietly! The videos do a great job of detailing all necessary steps. My wife was disappointed that we didn't end up with a new dryer, but spending $45 to save $800 is awesome in my book!

I followed the varied instructions out there for getting the dryer open. WATCH the videos on uTube; I took out more screws than needed on first attempt -- which isn't a big deal but took me longer than it should have to pull it apart. It appeared the grinding was coming from the dryer bearings due to some abrasion I could see and worn front slides, so I replaced the front slides (4) and the rear bearing. The kids helped by crawling inside the drum to tighten the new bearing bolts (just for fun). When I put it back together it was making a somewhat different grinding noise. It wouldn't make any noise until I put the belt AND front cover on and then it would make a periodic (about every 10 degrees) grind when I rotated the drum; I took it apart and the grinding would stop even if I rotated the blower by hand. Put it together, the grind would start .... It took me awhile to figure out that the blower retaining bolt had come loose so the plastic blower was grinding on the metal cover. CHECK THE BLOWER RETAINING BOLT visible from the front with the dryer door/cover off -- it's not obvious that it's loose by looking at it since the retaining clip still sits over the blower shaft even when it's loose. You might even see small nicks in the blower fan blade. It's super quiet now.

I was certain there was a cat stuck in my dryer -- there was a loud squeal and grind. Must have crawled in through the outside vent?? After fighting with many screws trying to get the dryer apart I figured out there was this thing called the internet and watched some videos -- too easy. Pulled it apart and saw some grinding on the front where the teflon slides were and pulled out the drum to check the rear bearing -- seemed sloppy so I order those parts and then some. Parts came fast. Put it together with the kids help from inside the drum to screw on the rear bearing from inside -- gave the drum a roll just for kicks. Put it all together and found it would grind when the belt and front cover were on, but was quiet when the belt was off -- hmmm. Still couldn't find a cat anywhere inside the thing. Checked the blower, idler wheel, motor -- all seemed to rotate quiet and fine by hand without noise or friction. Read some more on the new fangled internet listening to different permutations of grinds and squeels. Only lead was to check the blower retaining bolt which had looked fine. Threw a socket on it and sure enough it was way loose and the blower had some very small nicks in it -- probably from the dm cat going through it. Turns out when I was checking it I was pushing it just far enough in that it wouldn't grind. When I put it back together the rotational force would cause it to slip back out and grind. I did see this shaggy ferrel cat in my yard today -- so I'm still not sure if I actually fixed anything or if he just crawled back out.

The handle I ordered snapped into place in less than 5 minutes. It works perfectly. Thank you so much. . .

First I unplugged the power to the dryer, opened the dryer door and removed the two srews from under the hood of the dryer, then i removed the lid completely. then there is a screw on both sides of the drum which i removed (stubby screwdriver is highly recommended). then i lifted the front door of of the bottom plates, disconeccted the wiring on the bottom left that way i can replace the the front drum bearing very easily. I replaced the the front drum bearing and the drum bearing slides, there are 4 total(2 white and 2 grey). and then put back everything the way i took it off. It was a very fast and easy fix.

Pulled old Timer knob off and put on new timer knob

After taking the dryer apart I determined that the drum had completely worn away one side of the front bearing including all the bearing drum slides. I replaced the front bearing drum and four slides and the front air duct assembly due to it being cracked in several places. I figured I would also replace the rear drum bearing due to wear and cracking since I already had the machine apart. Since the repairs it works just like new. Thanks PartsSelect.

Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.

All I did was stick the knob on. How easy was that! Knob works every time. Very pleased with the part.

I am a female with little repair experience. I looked up model number on my dryer, Googled my proble, and fond your site. I used your "my dryer is doing this..." link. Ordered parts and completed job all by myself. The video was amazing! My husband was so excited that we didn't need to spend $400 on a new dryer (only $43)! I will use you again for other appliance issues. Great site with great information.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.