DBL333EA1WW General Electric Dryer - Instructions

Slid off the old START knob, then pushed on the new START knob.

I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.

My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.

My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.

I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com

Removed the damaged knob and replaced it with the new knob. Very ease

First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted to the control panel. I had no idea, so I did what was necessary to remove it. Needless to say, I bent the hell out of the hole that the switch mounts in. In turn, the installation of the new switch did not go as easily as I would have liked. After straightening out some metal and drowning the thing in epoxy, the new switch is installed. I hooked the wires back up on the back of the switch, plug in the dryer, and dry some clothes. Standing victorious over the dryer with beer in hand, not only did I accomplish the mission but I learned my lesson... destructive removal = BAD!

Unplug power. Take the top off. Take front off, unplug the two wire connections. Undo belt from back access. Pull up on drum and remove. Unscrew 4 screws that hold on the element housing, remove. Reverse steps to put back together.

One of the easiest repair jobs I've ever done. First I turned off the power. After removing 4 screws and lowering the cover of the control board, I disconnected the two wires attached to the switch. I rotated the switch counterclockwise and removed it. Just reverse this process and I was done. I was in and out in less than 10 minutes.

ordered part on line--received in mail 2 days later--
just pushed on in 2 seconds--job done

how much easier can it get??????

About a year ago I had to replace the front sliders. I had thought at the time that I should replace the belt and check the rear bearing, but I was in a hurry, and the wash was backing up, so I didn't do it. Oops. Within 6 months dryer started squeaking. Did I get around to pulling it out, and greasing rear bearing. Nope. Dbl oops.

Luckily on this model, everything is pretty basic, strong, and well made. The rear bearing after 9 years of constant use (5 person family)had simply run out of grease, and then worn into the plastic housing that holds the rear bearing. NOTE TO ALL -- probably too late if you're reading this -- but just grease your rear bearing by using a grease gun with high temp grease (car bearing grease works fine)through the small hole at back of dryer dead center of drum. It will take 5 min, and probably prevent the need for this repair, or delay it substantially.

Unplug dryer, turn off gas, and disconnect gas hose and duct hose. Inspect the latter two and consider repacing while you're at it. Move dryer to where you can get at front and back without cursing too much.

So...take a putty knife, and put a little masking tape around the blade if you're worried about scratching the finish on your dryer. If you're doing this repair, your dryer is probably at least as old as mine, and you can skip the tape and just bear with some small scratches.

Slide the putty knife into the groove between lid and front of dryer and pop up. (held by spring clips)

Now tip up lid and slide back, you may have to wrestle it a bit, or it may come off like a charm. Put it out of the way.

Take a sec to look at the interior wiring (you unplugged the dryer, right?) If you see any worn or raw spots, take some electrical tape and fix. Should be fine though. Take a vacuum and suck up any extraneous lint, dirt etc.

Tip dryer up slightly and block with wood or a brick. There are two screws at bottom -- undo these. IF they're missing, no worries, they're not critical. Put dryer back down.

Get a trouble light or a good lamp and shine ti wher you can see interior of dryer. There are two screws, one on each side on the INSIDE of the dryer, connecting the side panels to the front. Undo those. Put them in a little baggie and mark them "interior fr screws." I know, you're thinking "I can just remember them." But trust me, this way, you can't lose them or screw up. Now use the putty knife to pop the front panel off the sides. Do this gently, and don't yank the front way back, as the drum will drop. Oh, on mine there was a yellow plastic doohicky in the middle at top. Take that off too (one tiny screw) put the screw back in part way and stick the doohicky in the baggie.

OK, so the front panel should now be loose. It is still on a couple of little tabs at the bottom, which you prefer not to bend. So lift the front slightly and then back it out, while you (or preferably a helper) holds the drum so you can let it down gently. The front is attached to all sorts of wiring. You don't need to disconnect ANYTHING. THe front should be able to be moved away to the right like a door. Rest this up against something so as to not strain the wiring. On the front of the door are the felt and plastic sliders. If they look beat up or worn, replace them now -- or like me, you can do the job twice... That part is super simple...

Now, got back of dryer, there is a vent at back bottom. Remove three (or less) screws) and remove little door. Probably substantial lint here. Vacuum like crazy. The belt comes down around the drive pulley, and then up and over the idler pulley (to keep tension on belt. IF this feels loose/easy to move, replace the belt. In fact, if the belt is over 5 years old, replace the belt. (or when it breaks, you get to open everything again). Just unhook the spring and the idler will be loose and you can remove the belt off the pulleys -- it's now just around the drum. Slide the idler pulley off the stem

The switch made a humming sound when I turned it so I thought that might be the problem. Using the instructions on this Web site I took the top panel of the dryer off (after unplugging it), unplugged two wires leading from the switch (needed pliers for this), and removed the switch unit by rotating it counterclockwise (when behind it).
The replacement part came in two days. The installation went a lot quicker-maybe ten minutes.

Unplugged dryer. Removed screws from top of operating panel. Removed wires from switch. Turned switch 1/4 turn to left and removed. Replaced switch. Turned 1/4 to the right. Re-attached wires. Replaced operating panel and screws. Replaced knob. Plugged in dryer. DONE!!!!!!
Easiest repair ever! Thank you.

Removed 6 screws from the back panel and lifted/pushed the metal back panel up. Removed/sliced out the start switch by hand. Replace the new start switch and tightened all screws. Replaced the new selector Knob and it worked like charm.

Pulled off old knob put on new one

We unlatched the top of the dryer by pushing a screwdriver under the two areas where there were metal clips holding it down. We then removed the yellow clip screwed onto the top frame. We removed the front frame of the dryer by unscrewing the two screws holding the front frame on--one on either side. We didn't undo the wiring to the controls, we just kind of pivoted the front aside. We pulled the drum out from the plastic holder attached to the back of the dryer frame also unwinding the belt encircling the drum. Then we unscrewed the 3 screws holding the bearing to the back of the drum. We removed the plastic that had held the bearing by undoing the screws to the back of the frame. We installed the new bearing by screwing it to the back of the drum with 3 screws. We installed the plastic holder to the back of the frame by 2 screws and put the little ball bearing in. We used the grease that came with the kit to grease up the plastic where it held the big bearing attached to the back of the drum and inserted the drum back into the body of the dryer frame, pushing the bearing into the plastic holder. The hard part was getting the belt back around the drum and through the pulley on the motor that holds the belt. When that was accomplished, we put the yellow plastic holder back on the front frame with the screws and put the front back on after thoroughly cleaning the inside bottom area where there was a lot of lint. Then we snapped the top back into place.

unscrewed the back plate off of the dryer. Disconnected the the wires off of the switch. Remember to to unplug your dryer from the wall first!!!. Reconnect the wires to the new switch and twist back into place. Be careful not to bend the metal tabs. Put the back plate back on and plug in. Put on new knob and the wife was smiling. Took about 8 minutes to repair.

a. researched internet to find how to access rotary starter switch
b. isolated all electrical input at breaker box
c. removed 4 torx screws on top of dryer head
d. lowered dryer head (swivels toward front)
e. pulled electrical connections from back of switch
f. turned and pulled thus releasing rotary switch
g. reversed procedure above
h. reconnected electrical
i. started dryer - it worked first time
j. watched football until wife came home
k. told wife dryer was fixed and what a bear it was to get it done :o)
l. that night accepted my reward for working so hard at fixing the dryer and saving us a bundle. :o)
m. now we are both smiling

Troubleshooting was the hardest thing to do in this repair. the first thing I found wrong was the thermal overload was bad. That was easy to replace since that is on top of the housing for the heating coils and easy to reach. Only 2 screws hold it in place. Once I replaced that the dryer would start but, the temperature was off the chart. Now I know why that part broke. The control Thermostat was a little harder. That is held in by 2 screws but it is in an awkward place. I replace the 2 slotted screws with nut driver type screw which made it easier to place the screws in such a small area. Once the control thermostat was replaced the dryer worked great