Quick Question!

Have you ever purchased from PartSelect.com before?

Models > DBB3300GA2WW

DBB3300GA2WW General Electric Dryer - Overview

Get Parts and Repair Help for DBB3300GA2WW

If you know the dryer repair part you need, you can browse the list of all parts on the DBB3300GA2WW, or you can search by name or part description. You can also find your part by where it is located on the DBB3300GA2WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for DBB3300GA2WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.69

Drum Bearing Slide - White

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide functions by supporting the front drum as the drum rotates. This...

$44.72

Front Drum Bearing

This front drum bearing helps your dryer operate as quietly as possible. It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. This is an OEM part and is sold individually. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing.

$17.11

Timer Knob

This is a timer knob and it is used in conjunction with your dryer. This knob is white with a silver trim, it measures to have a roughly three-inch outer diameter, and it accepts a...

$6.17

Duct Felt Seal

This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.

$23.59

Drive Belt

This is a dryer drum drive belt. It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps aro...

$4.54

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start, shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This part is sold individually, and is a genuine OEM part sourced directly from the manufacturer. Although this part fits with some different brands, be sure to check the list of brands below to make sure this part fits with your dryer unit.

$51.71

Rear Drum Bearing Kit

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. Thi...

$10.88

Door Handle - White

This part is on the outer door of the dryer.

$38.53

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

$36.90

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Timer knob cracked and would not turn on the dryer

  • Customer: Kathleen from Greenwood, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 163 of 239 people found this instruction helpful
Very easy. I just snapped the new timer knob on and I was ready to go. read more

original duct was broken

  • Customer: Chad from Gilbert, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 122 of 140 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more

Dryer would get very hot and then turn off

  • Customer: David from Auburn, MA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 250 of 529 people found this instruction helpful
It was actually my father, he doesn't use the internet. He thought that because the dyer got real hot and then shut off he thought the thermostat wasn't working and the high temp shutoff was okay. He went through the manual and found the part and took it out. He called the service number but they wanted $50 dollars plus shipping. I saw it was a Thermo-disc p... read more