Models > DB3710DB Samsung > Instructions

DB3710DB Samsung Dishwasher - Instructions

All installation instructions for DB3710DB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DB3710DB
16-24 of 24
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishes were not getting clean on the top rack.

  • Customer: David from Billings MT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

Top rack wasn't getting clean

  • Customer: Craig from Justice IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
This couldn't have been easier. After unsnapping the docking station from the dishwasher, I aligned the two flapper valves that come with the unit and pressed them into place. I then pushed the new unit into place by pushing first on the left side and then the right until it clicked into place.
I looked at the old one and found that one flapper was gone and the gaskets were deteriorated. What made the whole process easier was buying from PartSelect. I have bought from them before and will again.

docking station seals were badly worn not allowing water pressure to spin the rotating arm.

  • Customer: Lonnie from Hollidaysburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
unsnapped old docking station and snapped in new one. woks just like new. thanks partselect.
I'll be back.

Dishes were not getting clean found that a part was missing from factory.

  • Customer: Steve from Ossineke MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We removed upper basket by snaping open and removing rollerslide caps. The docking station simply snapped into place. It only snapped in one way so we were certain it is installed correctly.
That part was missing from the factory and I feel a little angry that we had to buy it and install it ourselves. We would never have known why our dishwasher wasn't working like it should if we hadn't seen the inside of another one that belonged to a friend.

the top rack of dishes were not getting clean

  • Customer: Ellen from New Patlz NY
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
the part we received has changed, and so it did not fit our dishwasher after all. i was able to remove one flapper from the part and put it on my old one, and now the water pressure is much better, and the dishes are actually getting cleaned.

Dishes not cleaning due to worn gasket on docking station.

  • Customer: Peter from Seabrook TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
Removed dish racks, snapped out docking station and snapped in new station. Works great! Saved big bucks. Thanks.

Dishwasher not cleaning dishes

  • Customer: John from Covington VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The docking stations just pulled of and snapped on. I took the tube in the back out to make sure the docking stations were seated well but I'm not even sure that was needed. Very easy. Another contributing factor was using rinse aid with an all-in-one gel pack detergent. I let the rinse aid run out and it's been working great ever since.

Not cleaning top rack

  • Customer: JOSEPH from ST. LOUIS PARK MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After installing a new filter, :( I tried this. I wish I would have done this first since it's way cheaper and easier!!! If your dishwasher slowly starts to decline in its ability to clean the dishes, it's probably this problem.

Dishwasher was leaking

  • Customer: Sammie from Fort Sumner NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered part #2099940. Removed existing gasket, cleaned the area and replaced it with new one - so simple. No tools required.
All Instructions for the DB3710DB
16-24 of 24