D140 Jenn-Air Range - Instructions

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.

Most of the repair was obvious as I took the blower apart before ordering the parts. Unfortunately the new motor was significantly larger than the original motor so I had to um. Adjust the position of some of the other parts to fit it in. There was a sheet metal flange that was installed on the other side of the blower from the motor which was designed to focus the air flow into the blower. I used a hammer to ajust the angle of flange so it no longer extended as far into the blower housing.

It works just fine although its a bit louder than the old motor was.

1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.

(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)

Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).

The oven seal replacement was very straight forward. Two screws held the door to the arms coming from the oven. I slid the door up off the arm and moved it to a workbench. This whole process should take about 15 minutes, a little longer if your unit is older and you want to clean as you go. Mine was fairly dirty and I gave it a cleaning as I removed parts. Unscrew all screws on the outer frame of the door, including two small ones on the side. Remove the outer frame and then the glass front and set them aside. A few more screws to remove the glass from the inner door, and even more on the remaining part of the door. You should also remove the screws holding the tiny brackets as well to release the portion that holds the oven seal in place. This is very straightforward, just keep pulling screws out until you can remove the old seal.

Once the old seal is out, insert the new one using the wire embedded in the seal as your guide...the gap in the seal goes to the bottom. Put everything back together and re-install the door. My door hinges were spring loaded and took a little effort to move them down so the door can be slipped on. This is a two person job since the hinges do not lock in place, they spring right back up flush with the oven and you cannot install the door. Re-install the two set screws holding the door to the hinges and you are done!

With the new seal in place, it felt a little puffy and the door did not seem to close as flush as it used to. This makes sense since the seal is new. I kept the door locked (like you would to use the oven cleaning cycle). I even kept it partially locked during cooking.

Frankly, the hardest part was the cleanup of nasty grease and dirt that built up over the past decade or so.

Best of luck!

Just placed it at the filter location. Liked the ring feature on the filter for ease of removal for cleaning. My previous ones didn't have such feature. Thank you for filling my order. I bought an extra filter for the future. I'm a big user of my Jenn-Air range. I may soon be needing to replace my griddle. Will be contacting your company then.

Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.

I simply lifted off the grille in the center of the stove, pulled out the old filter and dropped the new one in. It sits at an angle (right side down, left side up) rather than slotting in to a particular spot.

First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.

First I turned off electrical power to the range by turning off the circuit breaker for the range.
Then I removed the two screws that hold the switch plate to top of front of range. Then I pushed the sw plate back toward to rear of range to disengage it from the guide pin, and lifted the switch plate and switch. Turned the switch plate over and labelled the four wires to the switch. Removed the wire which were push-on. Which allowed me to remove the switch plate completely from the range. At my bench I used my Dremell with a cutting wheel to cut off the two push nuts/washers holding the switch to the switch plate. Removed the old switch and replaced it with the new one. Pushed to the new push nuts/washers provided in the kit, and re-assempled.

Simple Repair!
Turn off Power
Remove four screws under panel.
Remove old burner knob.
Drop Burner Panel from range
Remove 5 wire connectors from old burner control
with pliers
Remove 2 screws that held burner control to range
panel
Install new burner control
Rplace two screws to burner control
Replace 5 wire connectors to new burner control
Replace 4 screw under panel
Replace knob to new burner control
Turn on electricity
Made wife happy!

It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

One oven door hinge spring was broken. I ordered two hinges to complete the repair.
The repair could not have been easier. I removed the door from the oven an unscrewed the outer frame of the door from the inner door assembly. I unscrewed the old hinge assembly and replaced them with the two new hinges.
I set the door back on the oven and replaced the oven door retaining hardware.
After replacing the retaining hardware, I removed the temporary shipping pins that keep the spring assembly static. Very important: don’t remove these hinge pins until the door is on the oven an the oven retaining hardware is secured.

Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.

Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process.