CYG4000AWW Magic Chef Dryer - Instructions

removed heating element, thermostat, and then replaced fuse. sorry, the control thermostat was not the problem. it was the fuse kit that failed. the control thermostat would have been easier to replace.

I followed the directions from a post on parts select that somebody had previously written and my repair worked out perfectly. I removed the top / lid of the dryer by placing a flat head screwdriver underneath both top front corners which was relatively simple. I then removed the entire front door of the dryer by disconnecting the electric wires for the door which again was a very simple procedure. The tumbler was now exposed at which time I removed the belt (I took a picture of the belt setup for later reassembly) and lifted the tumbler off giving myself easy access to the rear drum rollers and front drum pads. I was able to see that the wheels were worn and definitely the cause of the squealing. I changed out the wheels with replacement wheels which was self explanatory. The front pads were in good shape but I figured that at this point it would serve me well to replace them also which I did. I then reset the new belt (another part that I opted to change while I had the opportunity) on the tumbler with the picture in hand and had no problem. This step did require two people but still not a difficult step. I then put the door and lid back together and now had myself an extremely quiet dryer and a piece of mind that new parts were installed. All in all pretty easy repair.

unplug dryer, lift top, remove 2 screws holding front, lift & swing front to right, use nutdriver to remove two screws holding igniter and other piece attached with same screws, a couple wiggles and out, unplugged igniter, plug in new, reposition new igniter and other piece, replace screws, repositioned front panel, replaced front panel screws, dropped top back in place, plugged in and wha-la. Heat.
Original Igniter had a hairline crack in it causing it to intermittantly fire. Thanks PartSelect, right part and speedy delivery.

Web search to determine probable cause then search to find parts. Parts Select came through with the parts and quickly. Opened the top of the dryer (after disconnect from power-hate the smell of burning flesh) and found the parts that had up and died. Removed two screws for first part then one more and a lot of cursing to remove the other. Reassembled in reverse order, more cursing the tight space. Dryer back in service, wife happy. Only minor blood loss from sharp parts of machine. Success!

Unplugged the dryer then popped the top off and tilted it back, exposing the drum. Then using a flat bladed screw driver, removed the two sheet metal screws holding the front panel on. Once the front panel was removed, I pulled the drum off, exposing the motor and worn pulley. I removed the pulley arm, then removed the pulley. The bearings were totally gone, so I replaced it with a new pulley, replaced the belt and the front drum glides, since they were obviously worn. While it was apart, I cleaned out the interior with a shop vac, which greatly improved the efficiency of the dryer.

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

I inserted the clip

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

Easy Job.
First take a flat head screw driver and pop the top placing the screwdriver in between the front panel. The top of the dryer should pop up.
Then just pull it up and over towards the back.

Then unscrew the front panel and move it out of the way leaveing the front door atached to the panel.
Once you open the front panel' You can pull the dryer tub out by sliding it out and at the same time you need to push the belt towards the back of the tub until it comes off.
Now you can get to the ingiter by first disamablethe gas
housing first.
Simply by taking one screw off and disconnecting the gas line fitting in front of the dryer. Also disconnect the 3 sets of wires that are connected to that piece and the igniter.
The hole piece will then come out with the igniter attached to it.
Next disconnect the igniter from the piece and replace it with new one.
Then put back togather the same way you took it apart.
Reinstalling the tub.
When it's time to put the tub back in; there's a trick to that.
Put tub in about 3/4 of the way in, put the belt around the tub and let the rest hang to the floor inside dryer.then crawl into the tub and stetch your head and arm through the tub on the back side.
Then you can get to the belt and route it into the motor and the pully that is spring loaded it makes it so much easer that way then trying to run the belt and route it in place from the top. Once that is done now you can adjust belt back to its orignal position then push the tub back in place. Reinstall fron panel and your their.
Total cost 36.00 plus shipping. Thats a lot cheaper then a sevice call and labor

Verified power to the dryer with a volt meter. Identified the high limit fuses under the top cover. I used an ohm meter to determine the fuse located on the heater housing assembly was bad. The fuse located at the top (blue label) was not bad but I changed it since a new one was sent in the kit. Reassembled the dryer and it has been working ever since. Found the problem on a Monday and ordered the part. Received the part on Wednesday and the problem was solved. Cost me about $31. Would have been triple that if a repairman would have been called. Thanks PartsSelect

Before anything else, I would like to thank your company for a quick response and fast delivery of the parts that I ordered. Ordering parts from your company saved me a lot of money. The repair took me about 15 min. First I removed the two screws that hold the front cover and then I pulled out the drum and replaced the broken pulley, then I put back the drum and the belt in place and then I put the cover and screwed back in and now I'm back washing and drying pile of clothes.

(Electric) I opened the lid and propped it back on wall. The first piece was located all the way in the back mounted toward you. Easy enough. When it came to the thermal fuse, it was a bit trickier. It's located on the right side of the heating element wall. There is a screw straight on top of the wall. Mine was covered in lint, hence the thermal repair work:) Take the screw all the way out. The fuse is removed by lifting out the thermal fuse mounting bracket. Nothing special holding it in place. Just put the new one in the same way the old one came out. It was a bit difficult to wiggle the bracket back in, but I kept playing enough and it finally lost the battle. Put the screw back in, taking care to make sure it threads on top of the bracket to secure it against the heater element wall. Worked for me! Thanks everyone.

First I removed the screws that held the part in place, but this proved to be the hardest part for me. I had to find the right kind of screw driver . It was not a slotted or Phillips. It was more star shaped. Once I had the right tool, the rest was pretty easy.
I then opened the top of the dryer to be able to lay the front on the floor. There were wires connected to the front, however, so I had to remove the part that the wires were connected to by slipping it out of the bracket that held it in place. Once the front panel was on the floor, I simply lifted the old part out and placed the new part in. I closed the front, replacing the part with wires back into the bracket, locked the top down tight, replaced the screws, and I was finished.

First off I want to say I ordered my motor on Sunday night at 11:30 PM on veterans day and got the two day delivery. My part was sent out on that Monday (fed. holiday) and I received it Tuesday around 1:00 pm after I disconnected the wiring harness, took the blower fan C-clips off, unscrewed about 6 screws, and pulled the assembly apart I just done everything in reverse and replaced the new motor. I discovered that my thermostat fuse was blown so I ordered the High temp thermostat kit from here (two day delivery) on Wednesday at 10:30 PM and got the parts Friday at around 2:00 PM. After taking out four screws and four wires I replaced the fuse and high temp. set, pushed the start button to see if it worked and it started up like new. Now it heats twice as fast and everything doesn't have a light burnt smell. So dry time is faster (no more 80-90 min. cycle times), less dryer sheets (to cover smell) and all this added up to cost savings on electric bill and dryer sheets. It took a week to get my dryer back (because I just looked at the motor) but in the end I needed the fuse and motor. The quick turn around time to get the parts, the pictures to see if I had the right parts, and the ease of ordering the parts meant only one run to the laundry mat, and that wouldn't have happen if the dryer hadn't messed up on laundry day.