Models > CYG3005AWW > Instructions

CYG3005AWW Magic Chef Dryer - Instructions

All installation instructions for CYG3005AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CYG3005AWW
361-375 of 392
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The video showing how to do the install

  • Customer: Richard from cincinnati OH
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I tried to do the repair like the video said. My dryer was different. Using a putty knife to get the dryer lid up did not work There was 2 screws on each side holding the dryer top down and had to be removed. Did not have to take drum out.

Replaced belt, fronrt felt, glides

  • Customer: Angel from Georgetown DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Not quite as show on your repair intructions. But, all in all not that difficult. Things went very well. However, in the midst of the repair I found I had to replace other worn out parts.

Heats up for about five minute and shuts off gas only.No more heat.

  • Customer: Asrat from Signal hill CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ordered on line from part select , all sensors; cycling thermostat , thermal limiter.....etc. fuse,and the two coils. Most parts arrived in two days. My last order - coils & limit switch arrived in three working days.Installing these parts took about 30mins. to 1 hour. I believe the last two fixed the problem. It is working perfect.Partsselect , will use you again.

NO CLOTHES DRYER HEAT

  • Customer: David from Cornelia GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
FOLLOWED THE INSTRUCTIONS SHOWN IN THE VIDEO. VERY EASY,

would not tumble

  • Customer: DAVID from HIGHLANDS RANCH CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I first unplugged the dreyer from the wall, I then used the putty knife to push clips in on top of the dreyer and opened the top. I used a nut driver to remove the front panel and unplugged the light and door switch wires. I then reached under the drum and removed the belt, and then lifted the drum out of the cabinet. I used snap ring pliers to remove the rollers and replaced.them with the new ones. After installing the new rollers I placed the new belt around the the.drum and lifted the drum by the belt placing it back into the cabinet. With the drum back in place I reattached the front panel and turned the drum to make sure it was not hanging up on the felt rings. With the drum moving freely and the belt hanging down I layed back in front of the dreyer and put the belt on the motor and reached up to.the tension pulley and placed the belt under the pulley. Once the belt had tension on it I again manually rotated the drum to make sure it wasn't binding anywhere. All was good so I replugged the light and door wires, shut the lid and plugged the dreyer back into the wall socket, turned it on and it worked great. From start to finish it took about.40 minutes and half that time was spent cleaning out the cabinet which had quite a bit of lint. I have used the.dreyer several times since the repair, and this completely took care of the problem. I highly recommend ordering the rollers along with the belt as mine were well worn and it saved me from having to take it apart twice. All in all a very eazy do it yourself project.

Replaced pressure door switch

  • Customer: Robert from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Too simple to describe.

Belt cut in two

  • Customer: Herminigildo from virginia beach VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
First I take off all front cover and then the dirt strainer next is the dryer drum holder next the top cover I lift up and so you room to set the dum belt

Dryer runs but no heat

  • Customer: Wayne from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I popped the top open by depressing the spring clips with a putty knife. I then used a socket to remove the two bolts holding the front panel on either side near the top. Once the front panel was removed, I removed the frame that supports the front end of the tumbler drum. I then removed the belt tension by sliding it off the motor tensioner and removed the drum. Once the drum was out I had easy access to the high limit thermal fuse that I had to replace. After the fuse was replaced I put it back together the same way I took it apart.

Black connection at terminal block burnt. Black wire was burnt through.

  • Customer: Wayne from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the dryer. Used the putty knife to release the spring clips. Opened the top and photographed then disconnected the wires at the top of the terminal block. Removed the old power cord and terminal block. Installed new terminal block. Reconnected wires according to pictures. Installed new power cord.

Broken drive belt

  • Customer: chris from bakersfield CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
I was amazed just how easy it was. It would have been much quicker if I had a nut driver instead of a wrench. The video was great. Thank you!

No heat

  • Customer: Steven from Oak Lawn IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.

Door catch broken

  • Customer: Martin from Grapevine TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

No heat

  • Customer: Nancylee from Boone IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off dryer 220V breaker at panel. Remove front kick panel (two 5/16 hex screws at lower corners). Check continuity of high limit thermal fuse with meter; no continuity: fuse blown. Remove two wire clips with pliers. Remove fuse with nut driver (two 1/4 hex screws). Install new fuse. Replace two wires. Replace kick panel with two screws. Reset breaker at panel. Reset, start timer: dryer has heat.

Male door latch would no longer catch.

  • Customer: Joan from North Myrtle Beach SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

When I turned on the dryer it made a squealing/screaching sound.

  • Customer: Robbi from Centennial AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions provided by Partselect. The video and information were very clear and accurate. I have never taken a dryer apart, but have some tools and the cost savings plus the reward of fixing it myself were enough to inspire me to try. I was so happy with this experience I recently diagnosed and fixed a friends dryer with the helpful information from Partselect.
All Instructions for the CYG3005AWW
361-375 of 392