Models > CYG3005AWW > Instructions

CYG3005AWW Magic Chef Dryer - Instructions

All installation instructions for CYG3005AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CYG3005AWW
16-30 of 378
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would not heat up.

  • Customer: Roger from Bonners Ferry ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 18 people found this instruction helpful
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the front open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++

Dyer would not heat, flame would shut off within 10 seconds

  • Customer: Christy from Riley MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 16 of 20 people found this instruction helpful
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.

Blower fan cracked

  • Customer: Rick from Birch Run MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 18 of 26 people found this instruction helpful
Unplug the power cord from the unit. Remove the lower front panel; then the upper front panel including the door (unplug wire to door switch). Then remove the cover on the fan housing. Need to block the motor from turning; I used a stick to jamb the front of the motor; then unscrew the old blower fan and screw on the new one. Then replace the cover and put front panels back on.

OLD DRYER KNOB BROKE

  • Customer: Donald from Keystone Heights FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 27 people found this instruction helpful
WIFE WANTED A NEW DRYER AS IT WAS USELESS WITHOUT A KNOB AND TIRED OF USING PLYERS TO TURN IT.

WENT TO INTERNET, ENTERED DRYER KNOB, LEAD ME TO YOUR SITE AND ITEM WITHIN TWO MINUTES. ORDERED AND RECEIVED IN 2 DAYS. NO TOOLS NECESSARY, JUST PUSHED IT INTO PLACE.

SAVED THE COST OF A NEW DRYER.

Original belt finally gave way.....(15yrs old)

  • Customer: Garrett from Racine WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 12 people found this instruction helpful
Simply remove the front panel screws(2) at the bottom of the dryer. Pull bottom of panel outward until it swings free of the top(taking care not to pull the wires out). Rotate out of the way and remove the two left side screws holding the drum plate and snake the belt around the flange. Reinstall those screws and remove the same ones on the right side. Snake the belt behind that flange and reinstall screws. Then all you have to do is run the belt around the motor sheave and the idler pully and your done. Reinstall the front panel.

the door on the unit wouldn't stay closed

  • Customer: john c. from north beach MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 16 people found this instruction helpful
removed the dryer female part that was broken with needle nose pliers and inserted the new one, on the door i removed one phillips screw and r/r the male piece with the new one and re-inserted the screw. that was all, very easy repair

Dryer will heat up for 5 minutes and then will shut off

  • Customer: Carlos from Congers NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 12 of 13 people found this instruction helpful
The most difficult part of this repair was to diagnose it correctly. The dryer will run but will heat up for five minutes and then shut off and continue just on air drying. It will reset itself if you shut it down and restarted it again, to do just the same for another five minutes. All troubleshooting guides will tell you to replace limits, thermostat, flame sensor but nothing will tell you that the gas valve is shutting down.I found the problem after I bypass all limits to make sure that they were not dropping out and by process of elimination I came up with the gas valve.
The process to replace gas valve is as follows:
(A) Shut off incoming gas to dryer.
(B) Remove flexible connector from dryer located in the back of it.
(C) Remove all gas fittings attached to the pipe kit after removal of flex connector.
(D)Now place yourself in front of the drier and snap just the front of the top cover upwards without removing it.
(E) Place something in between the cover and the dryer drum just to keep the cover open.
(F)Disconnect the three wires of the door switch.
(G)Remove two 5/16" self tapping screws located in the top front (left and right) of the inside of the dryer.
(H) Pick up the front cover of the dryer and remove.
(I)With a phillips screw driver remove the three screws on the inside of the dryer that holds you air shoot and filter screen assembly.
(J)After the filter assembly is removed, clean all lint from blower wheel(now visible) and also from the filter assembly.
(K) Unplug all connectors to gas valve and also to the hot surface ignitor.
(L) Remove the flame sensor assembly with a 1/4" socket.
(M)With a 5/16" socket remove the burner assembly with extreme care not to damage the hot surface ignitor.
(N) Remove all three 5/16" screws that hold the gas valve and pipe kit.
(O) Remove complete gas valve and pipe assembly.
To install new gas valve assembly follow these instructions in reverse.
If you follow methodically all these instructions, you will have a successfull repair and remember at the end of this project your better half is going to know that you are a heroe.

Drum Not spinning

  • Customer: Dann from Claremont CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 11 people found this instruction helpful
First, I unplugged the dryer. Then I used a flat screw driver to pop the top open. I removed 2 bolts from the front cover and removed the front door cover. I also took pictures of the electrical connector on the door so I would remember how the wires went back on. Then I removed 4 bolts from the front drum guide and lint screen holder. This allowed me to remove the drum & old belt. While the drum was out, I pried an access panel open on the side of the dryer. I then glued the new back felt piece in place. I put the new belt around the drum and re installed it. I re-installed the front guide and front cover re-connecting the door electrical switch. With the access panel open, I attached the belt to the motor. I then plugged it back in and turned it on to verify operation pryor to snapping the top cover back in place. Very easy repair.

Motor would shut off in two or three minutes after starting.

  • Customer: James I from Henderson NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
I removed the dryer front and the drum, then disconnected the wires from the dryer motor and removed it from the motor mount, after installing the new motor in the motor mount the rest was just putting the dryer back together the same way I took it apart, the best way to do this is to print out the diagram from partsselect.com and follow it step by step, this was so easy everybody can do this and save alot of money for the labor and the parts mark-up, try it you all can do it (SO EASY)

Screaming noise and drum not turning

  • Customer: Robyn from Pullallup WA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 8 of 9 people found this instruction helpful
Removed top, remove front panel, removed drum assembly brace, removed drum and belt . The belt and rotor were shot. I replaced both drum support rollers since i was there. Then replaced the motor and Idler lever and pulley, the put the belt on and put everything back. This unit will last a while longer and the grand total including next day air 175.00. I tried to just by the motor locally but for 242.00 I got every thing listed above.
Thanks

The insert-molded nut stripped from the wheel

  • Customer: Ted from Grayslake IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 9 people found this instruction helpful
Because the wheel had stopped and the shaft kept turning (junk from child's pocket got in there), the nut stripped itself away from the wheel causing low RPM and low air movement (lazy flame, vibration and clothes not drying)

I had to use a screwdriver to break the wheel away from the center nut and remove the fan. I then removed the air fan housing (3 bolt behind the fan wheel). I used a small pair of vise grips to hold the motor shaft staionary while I used a pair of channel lock pliers to remove the nut that was molded into the fan from the motor shaft. It was harder to get the nut started then I would have thought.

Once complete, I put the fan housing back on and threaded the new wheel on easily. The motor has external fins on it which turn with the shaft-I held one lightly while I threaded the fan on to keep the shaft from turning. Tighten just slightly more than hand tight-don't go crazy-it's threaded to stay tight with rotation. Works great and very quiet now.

drier would not heat up

  • Customer: Joel from North English IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 13 people found this instruction helpful
first i checked the power supply then i checked each of the switches and limit fuses for continuity.
to do that i had to take the front of the drier off, four screws there. then i removed the bad limit switch 2 screws,the door switch was bad so i replaced it, no screws. since i had the front off the drier i removed the four screws that held the drum in place and replaced the belt. assembled the drier in reverse order when the parts came. 1/2hour total labor.

broken belt and idler pully

  • Customer: George from Haverhill MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 7 of 7 people found this instruction helpful
Remove front pannel
remove wires to light and switch
remove drum panel
disconnect motor wiring
unscrew motor mount
replace idlerlever replace belt reassemble all parts

Heat Would Not Come On

  • Customer: Lynn from Novi MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 8 of 10 people found this instruction helpful
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.

broken plastic vent

  • Customer: joe from Beacon Falls CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 7 of 8 people found this instruction helpful
I am not mechanical so if I can do it so can. UNPLUG THE DRYER FIRST!There are two bolts on the back of the dryer that connect the control panel and the dryer itself remove these and take out the brackets that are held by these two bolts, I used a socket, lift up and peek in to the front top you will see two screws that hold the other side of the top of the dryer lower the back side and move to the front of the dryer now that the back bolts are removed. Take a large screwdriver and place a dishrag or handkerchief so the flat side is inserted where these screws are located{preventing scratches}pry upward it will seperate the top of the dryer from the front of the dryer move over to the next screw and repeat now the top is loose and can be slid backwards until there is room for you to see down in front of the dryer, notice there are three wires that connect for the light on the right hand side, take the time to write down there color and in what order they are located as you will have to remove these now inside the front panel from the top about a third of the way are two bolts, one on the left and one on the right use the socket to remove these now pull the front panel to you and lift up, the front panel will now come off set aside. remove the three screws that attach the plastic vent from inside the dryer,pull out plastic vent, vacuum out dust and lint install new plastic vent install the three screws from inside the dryer drum and reverse the process you are finished!
All Instructions for the CYG3005AWW
16-30 of 378