Models > CYE3005AYW > Instructions

CYE3005AYW Magic Chef Dryer - Instructions

All installation instructions for CYE3005AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CYE3005AYW
46-60 of 418
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no heat

  • Customer: Janet from Portland, OR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 7 people found this instruction helpful
I first removed the two front screws on the front cover located on the lower half of the dryer using a flash light looking on the left side all the way to the back you will see two hex screws removing them will now let you wiggle the heating element back & fourth while pulling down it will come out in just a few seconds - then with your digital camera take a picture of the still wired heating element as to a clear reference for wiring the new element - first Aline the new element in the same direction as the old element and transfer them one by one check camera for assurance that you have done it correctly and re-reinstall in the reverse order

also I would recommend taking off that black plastic blower chute and cleaning it assuringly the best performance of air flow

dryer kept shutting off motor bearings where failing causing the motor to labor too much and the machine would shut down.

  • Customer: Michael A. from Wolcott, CT
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
First I unplugged the dryer, then I removed the bottom front panel. Then the door I marked the wires to the shut off switch on the door and removed the switch from the door. Next was the lint screen housing and duct work that goes to it. Then I had to reach under the drum and take the belt off of the motor pully and tensioner so I could remove the drum. I removed the drum. I then marked all the wires I had to disconnect. I took the fan housing front panel off. I held the belt drive end of the motor shaft with the pipe wrench, i could have used an open end or an adjustable wrench also. I used a 7/8 six sided socket on the plastic fan nut on the front of the shaft so that if it was hard to loosen I would have a better chance of not rounding the nut. I removed the fan and the back of the housing, unplugged the motor, and removed it. The clips that hold the motor to the motor bracket are a little tricky, I used a screw driver to remove them. I then replaced the motor and put everything back together. One hint you should know is to make sure you mark the drum front so when you put it back in you get it right the first time. I fits in both ways and will go back together but it won't turn free and you'll have to take it all apart again. I tried it by hand both ways and was able to catch the mistake before I put it all back together, but I could have put it together wrong.

rumble from drum, hard vibration from drum

  • Customer: Christopher from Severn, MD
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
The parts to replace were mounted to the rear wall of the dryer and only the front pane is removeable. With the panel removed the drum had to be pulled carefully straight out. The belt and tention arm were difficult to reposition. Since you have the appliance apart replace both roller and roller support brackets one of which you cannot see from the front. Throughly vaccum all lint and roller wheel debris . If you have an air compressor take the time to blow out the motor . Make sure to rig a device to hold the tention arm back with the belt correctly aligned while sliding the drum back into place. PARTSLECT is great , easy to use and suggests other parts I may not have thought of and quick . Parts were here in 2 days standard shipping. I was in the dog house for putting this off too long. My wife is happy so I'm happy.

Inner diamiter of roller support worn larger than pin

  • Customer: Stephen from Franklin, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
1. Remove bottom sill plate with two screws
2. Remove door, watch for the wire.
3. Remove tub retaining "ring" 4 screws
4. Pull tub forward
5. Pull off the old support roller using the snapring pliers
6. grease the new roller and pins (do both sides)

Reverse it and put it back together and its good as new!

Door safety switch would not close keeping dryer from running

  • Customer: John from Warsaw, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 11 people found this instruction helpful
Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

Dryer would not heat

  • Customer: James P from Agawam, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
First I turned off the circuit breaker, then removed the two screws that hold the front lower panel in place. Once open I removed the 2 screws that held the element in place. (Far back left side) I then pulled the element out leaving all wires connected. Wires are long enough to extend out to the floor in front of the dryer. I simply exchanged the wires one at a time to the new element so no mistakes could be made. Reinstall, reset the breaker, and Instant HEAT. Repaired for under $40.00

old latch broke

  • Customer: Jim from Germantown, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
I inserted the clip

Dryer would stop during cycle and then not restart. When I started the dryer, there was a short buzz sound as the motor started.

  • Customer: Bob from Denver, CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 6 of 9 people found this instruction helpful
First I removed the bottom front cover attached with two screws, then the main front cover attached with two screws. I then removed two more screws holding the top in place, detached three wires and raised the top lid. I held the top lid out of the way with a cord tied off to a cabinet above. I then removed four screws holding the front support panel in place and set it to the side with wires still attahced. Then I slid the dryer belt off the drum and removed the drum. Next I removed the cover of the fan wheel by removing several screws. This allowed me to unscrew the fan wheel (reverse threaded) by anchoring the motor shaft with a wrench and using a large socket to turn the nut end of the fan wheel (then was no snap ring). I then popped off the two clamps holding the motor in place and removed the motor. The only tricky part about assembly was putting the belt back on the pulleys once the drum was installed. You can't see the pulleys once the drum is installed so it is done by feel.

Noisy and not drying the clothes

  • Customer: Pietro from Fairfax, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 5 of 6 people found this instruction helpful
This was my first time repairing a dryer. If I knew when I started the project what I know now, it would have been an easy repair. First, you should know that the series number (used for selecting a wiring diagram) is the last two digits of the unit's serial number (not model number). In my case, the series number was 11. The hardest part for me was figuring out how to take the dryer apart. I made the mistake of starting with the top instead of the front. In fact, I removed the control panel and disconnected all the wires, labeling them carefully, and creating a diagram, so i could put it all back together later. I now realize I could have left that all together and just lifted the top up in the front without removing it. That knowledge would have saved hours of work, so I hope it helps someone (prop up the front a few inches and start by removing the panel on the lower front, then remove the screws on the main front panel, and then pull out the bottom of that panel toward you until the top of that front panel disengages from the top of the dryer - the rest is obvious). So it turns out there were two separate problems: 1) the blower wheel had broken completely off of the motor so it wasn't spinning - this is why hot air wasn't being pulled through from the heater in the back of the dryer; 2) the pulley on the spring-loaded lever arm attached to the motor was squeaking due to lack of lubricant. So the solution was to replace the blower wheel and spray WD-40 in the pulley (and also, for good measure in the roller bearings that support the drum in the back of the dryer). Most of the time spent on the repair was just due to my own mistakes. In particular, once I got everything back together after the repair, it stopped squeaking and there was good airflow, but it wasn't heating. I spent an entire day trying to troubleshoot the lack of heat. I tested and bypassed all of the thermostats and heater fuses and the heating element still wouldn't come on. I even managed to accidentally ground one of the leads from the fuse and had to replace a melted wire connector (trip to the Shack). In the end, it turned out that a wire which had been accidentally disconnected from the main power cord to the dryer, I had put back in the wrong spot. There is L1, L2, and neutral going into the dryer. I had the heater on the same circuit as the motor and other stuff. Once I traced the wiring diagram back, I realized this and corrected it by putting the heating circuit back onto L2. Now it "hums like a Singer". If everything had gone smoothly, instead of being a 2-day repair, it would have been a 2 hour repair. 2 hours instead of 1 because to get the leverage I needed to remove the old blower nut, I had to actually pull the motor assembly out of the dryer and move it to my workbench. Someone who is strong or more limber or has better tools might be able to skip that step, reducing the time by about 45 minutes. Good luck!

Lint Filter was cracked

  • Customer: Rex from Cary, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
Not too difficult. Take out of box, insert into dryer slot.
Done

No Heat

  • Customer: Rogelio from Loxahatchee, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 4 people found this instruction helpful
Ordered the new heater element on Saturday and got it on Tuesday. I have ordered from PartSelect before and the service has always been fast and accurate.

The first thing I did was to unplug the dryer and then removed the bottom front pannel by removing two hex screws, one on each side near the bottom of the dryer. Use a flashlight if you need to see better. I then used my shopvac to vacuum all the lint that had gathered over the years, including the old heater element located on the left side towards the back bottom part of the dryer. Located the two hex screws and unscrewed them to remove the heater element. Pull out a bit from the bottom and then down. Pull towards you and remove the wiring from the old heater element making sure where the wiring and parts to be reused go so they could be transferred to the new heater element. Re-attach the heater element with two hex screws. Replace front cover and plug in the power cord and start drying clothes.

dryer would shut off during dry cycle. It was difficult to rotate drum manually

  • Customer: Dave from Bend, OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 4 of 4 people found this instruction helpful
I looked at your on-line diagrams (exploded views) and basically used them as dis-assembly info.

I removed the bottom panel, followed by the front panel, the drum holders and drum.

Toughest part was the spring clips holding the motor in place,,,, but notes on your site from other folks doing the same motor replacement solved that one,,,,,, I used a flat bladed screwdriver and pliers to manipulate the clips both off and on

Lint Filter Air Dust Assembly broke inside the dryer.

  • Customer: Loren from Woodland Hills, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
I believe the best procedure would be to start at the very bottom of the machine - there are two sheet metal screws in the bottom panel. Remove the bottom panel.

Now, there are two sheet metal screws at the bottom of the front door panel that need to be removed. Remove front panel by pulling down to dislodge from plastic pins aligning it to the top panel.

Now the air duct assembly is accessible. From outside machine remove two sheet metal screws holding lower air duct frame. From inside the dryer opening, remove three screws holding the upper frame. Remove old air duct assembly and vaccuum machine.

New air duct assembly is in one piece, so only three inside screws are needed to support it. Make certain the screws are seated well or clothes could get hung up on the screw heads. Reinstall front door panel and bottom panel.

Doing it this way should make the job around 20 to 30 minutes.

Squeaky belt

  • Customer: Michael from Marietta, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Removal of the entire 2 front panels
Removal of the heat exchanger into the drum
Removal and replacement of the belt
Reinstallation of the heat exchanger, and both front panels

Won't tumble with clothes & making loud noises

  • Customer: Michael from North Hampton, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 8 people found this instruction helpful
Dryer would only tumble for ~15 min then stop. During this time it would be really loud. Turns out to be a bad Motor. To replace 1) Removed bottom kick panel by removing 2 screws. 2) Then removed upper front cover by 2 additional screws. 3) Disconnected thermostat (marking location of wires on paper). 4) Removed blower housing (3 screws)undid the rib belt from the drum by pushing the pulley wheel up so the belt could be loosened and removed from motor. 5)Removed the front cover of the dryer opening by removing 2 screws. 6) Lifted up and then puled it out to expose the drum. 7) Removed the drum w/belt from the dryer exposing the motor. 8) Removed 2 screws from the motor and disconnected the plug from it. Slid it all the way out. 9) Need to remove (3 screws) the metal faceplate from motor to access the blower wheel (plastic). 10) Unscrewed the plastic wheel and removed 2 screws to remove the motor from the frame. reversed the process for reassembly. Sounds tougher than it really was - only took 30-45 min. Suggestion - write down on paper location of any wires you disconnect - makes reassembly very easy. Also recommend vacuuming any lint in the dryer while it is completely accessible.
All Instructions for the CYE3005AYW
46-60 of 418