CWG4510AAB Maytag Wall Oven - Instructions

It is the first time that such a repair has to been done on my appliances.
The serviceman did a marvalous job after receiving the parts.
Within an hour the range was working a new.
Many thanks for the prompt service.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.

really easy thank you to your video

I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

Watch the video, it's too easy and best of all, the part fixed the oven!

I am so gald I found Parts select. I was going to order a Gas valve for $140. All the comments said the problem was a bad igniter. even though the igniter was glowing bright it was not drawing enough pawer to open the gas valve. I purchased the igniter installed it in 15 minutes and my oven works like new.

Followed the excellent instructions on your web site. I removed the oven burner assembly to make it easier to install the new igniter. The connector on the new igniter matched the one in my oven exactly. It helps to have the oven light on!

There was a lot of trepidation about starting this project. What if this is the wrong part? What if I hook it up wrong? What if the gas line is not properly secured when I'm done? This is why it took my 6 months to start this project. I hesitantly looked up my product number online and partselect.com returned three of the top ten results so I clicked it. One of the best moves I've made. When the product was shipped, I received an email with a video attached that explained how to install the igniter. This is what set partselect.com apart from everyone else and differentiated my experience from a "maybe i'll look around more next time" to "I will use partselect for all of my appliance part needs from now on" experience. Thank you for the quality customer care.

Remove oven door and bottom panel. Remove metal shield above the burner. Unscrew old igniter from brace. All this was straightforward. Then I found the old (long) igniter did not have a convenient plug that I could pull through the hole in the back of the oven. So I had to clip the two wires to remove the old igniter and stripped the insulation of these wires. Then I clipped the two wires of the new igniter since, unfortunately, I could not use the convenient plastic connector. I stripped the wires of the new igniter and connected both to the previously stripped wires coming through the hole from the back of the oven. I twisted on the ceramic wire nuts provided. It took 10-15 minutes or so to be confident these wire nuts wouldn't just fall off on their own. Then I stuffed the wire nut connections back through the hole, stuffed in all the insulation provided (necessary for the new (short) igniter!) and screwed the new igniter to the old brace. (I didn't need the new brace supplied or two long wires supplied.) Total time was about 70 minutes. The oven works well! This experience is much better than finding a repairman, scheduling the visit, etc.

look up part, read the diognosis, order part, watch repair vidioe, order part, install mystelf. success!

it was really simple with the kit and instructions that came with the kit everything i needed was in the kit, and hats off to you guys

followed video took 10 minutes, almost went anf bought a new stove

The only difficulty with following the supplied video, is that my ignitor did not come out as easily as a few turns of the screwdriver. The screws stripped as I tried to remove them, making them twirl in their holes. I had to apply back pressure for them to come off and free the ignitor for replacement. Other than that, the installation went smoothly, and the oven sprang to life within 10 seconds of turning it on.

I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".

I removed and replaced the igniter. I described these symptoms on the web site and it detailed that90% of the time by installing a new igniter it will fix the described problem. So I ordered the part and installed the part and everything worked OK. The only tool I had to use was a screw driver to remove three screws. It took about half an hour. If I had to do it again it would take about 15 minutes.