Models > CWEF310GSE > Instructions

CWEF310GSE Westinghouse Range - Instructions

All installation instructions for CWEF310GSE parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CWEF310GSE
31-45 of 532
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

In a seasonal house, a mouse got into the oven insulation during the winter. We have gotten rid of the mouse but when we used the oven we could smell mouse urine! Upon inspection we could see that the mouse lived and urinated in the oven insulation.

  • Customer: Susan from Newington CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
My husband removed the screws that held the top of the stove on and then lifted the top up. It is hinged. He then took out the old insulation, wiped down all visible parts of the interior with a bleach solution and replaced the blanket insulation with the new insulation. That took care of the problem!

Oven Racks needed to be replaced.

  • Customer: Peter from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Slide out the old; slide in the new!

Electric burner switch shorted out.

  • Customer: Armando G from Alice TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Oven door inner glass cracked after cleaning

  • Customer: Lisa from Erial NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

switch not always turn off

  • Customer: Jerrold from San Marcos TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

broil element was bad.

  • Customer: William from Fort Myers FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Bottom elerment burnt into

  • Customer: Danny from Gaffney SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 5 people found this instruction helpful
First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Bake element bad, broiler element OK.

  • Customer: Gerry W. from Oxford IA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

Large burner would turn on high and not cycle off

  • Customer: Kevin from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

Oven door glass cracked in half

  • Customer: Janice from Northbridge MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

new switch was not wired like old one

  • Customer: PERRY from LECANTO FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 7 of 16 people found this instruction helpful
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

Bake Element caught on fire

  • Customer: Judy from Spencerville OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 7 people found this instruction helpful
First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

the indicator light for burners broke and shorted agaist the back panel on range

  • Customer: James from Caldwell ID
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson

switch had a diffirent lug configuration

  • Customer: Robert from Andrews SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 10 people found this instruction helpful
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

The baking element developed hot spots and stoped working.

  • Customer: Jeremiah from Crawfordsville IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the baking racks and started the oven to burn off any factory oils on the baking element.
All Instructions for the CWEF310GSE
31-45 of 532