Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CWEF310GSE > Instructions

CWEF310GSE Crosley Range - Instructions

All installation instructions for CWEF310GSE parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CWEF310GSE
16-30 of 539
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

anti-tip bracket not installed

  • Customer: Brian from Panama City Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 28 of 36 people found this instruction helpful
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

Top Broiler element burned out

  • Customer: Richard from Alexander City, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 27 of 38 people found this instruction helpful
I disconnected power cord. Removed cooking racks. Removed element mounting screws. Removed back panel and removed wires on both ends. Pulled element out put new one in and bolted down. Reconnected wires. Put rear cover on. Plugged in and checked for correct opreation. OK!

If burner was placed on HIGH, it wouldnt lower heat once LOW setting chosen

  • Customer: Juilo from Lake City, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 20 of 21 people found this instruction helpful
I had to replace the switch in the back of the control knobs. I was very grateful to the female phone attendant who answered my call. Since my part number had switched a few times, she took the time to reverify the "blueprints" of my machine with the parts carried at Parts Select and she helped me be assured that I was buying the correct part for my machine. She was SOOOO helpful. Will definately buy again from your store.

My bake element (lower element) just about caught fire and needed replacing

  • Customer: Ryan from Greenfield, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 20 people found this instruction helpful
The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D

Broken bake element

  • Customer: Chris from DeRidder, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 19 of 23 people found this instruction helpful
From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.

Element caught fire when i preheated my oven

  • Customer: Michael from Union City, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 25 people found this instruction helpful
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

corroded terminals

  • Customer: Gary from hollywood, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 16 of 17 people found this instruction helpful
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff

missing oven racks

  • Customer: ALLAN from APACHE JUNCTION, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 16 people found this instruction helpful
order pcs fit perfect.

Front Burner was on high all the time when on

  • Customer: Gregory from Monument, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 15 people found this instruction helpful
Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.

Element shorted out

  • Customer: Patrick from Louisville, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 18 people found this instruction helpful
I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

Went to use the stove and the main baking element had a melt down.

  • Customer: Tracey from DEVILLE, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 17 people found this instruction helpful
shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

Element burnt out

  • Customer: Larry from Danville, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 14 of 18 people found this instruction helpful
The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.

new switch was not wired like old one

  • Customer: PERRY from LECANTO, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 14 of 24 people found this instruction helpful
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

Large burner wouldn't heat

  • Customer: Phyllis from Elberon, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 14 of 27 people found this instruction helpful
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

In a seasonal house, a mouse got into the oven insulation during the winter. We have gotten rid of the mouse but when we used the oven we could smell mouse urine! Upon inspection we could see that the mouse lived and urinated in the oven insulation.

  • Customer: Susan from Newington, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
My husband removed the screws that held the top of the stove on and then lifted the top up. It is hinged. He then took out the old insulation, wiped down all visible parts of the interior with a bleach solution and replaced the blanket insulation with the new insulation. That took care of the problem!
All Instructions for the CWEF310GSE
16-30 of 539