Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CWE5800ACS

CWE5800ACS Maytag Wall Oven - Overview

Get Parts and Repair Help for CWE5800ACS

If you know the wall oven repair part you need, you can browse the list of all parts on the CWE5800ACS, or you can search by name or part description. You can also find your part by where it is located on the CWE5800ACS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for CWE5800ACS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$29.46

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

$46.44

Bake Element (16" long x 16" wide)

This spade style bake element with push on wire terminals is 16 inches wide. It has a terminal depth of three inches and a total element length of nineteen inches. This element com...

$5.15

Screw

This screw is sold individually.

$22.22

2 Piece Broiler Pan

The top of this part is now black.

$20.63

Terminal Block

It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).

$5.15

Screw

This screw is sold individually.

$53.57

Broil Element - 3000W

This broil element is found on the roof of the oven.

$2.87

Screw (4)

Sold Individually.

$25.24

Light Cover Lens

This part goes over top of the light bulb.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 110 of 127 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

bottom heating element in oven disintegrated

  • Customer: DENISE from GERMANTOWN, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 43 of 46 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I threw away the old pieces.

Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and tightened them in.read more

F1-1 code

  • Customer: charles from marstons mills, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 47 of 60 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more