Models > CWE5800ACB > Instructions

CWE5800ACB Maytag Oven - Instructions

All installation instructions for CWE5800ACB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CWE5800ACB
31-45 of 144
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Indicator Lens melted and fell back into the control panel

  • Customer: Philip from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

Oven stopped working mid-bake and clock went dark

  • Customer: Steve from Marietta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 6 people found this instruction helpful
I removed the front panels and took out the clock. Clock removal was done two or three wires at a time. I hooked up the old wires to the new clock as I went. There were about 7 wires. This ensured a proper hook up. Reinstalled the front panels, and back to baking dinner.

oven not heating to set temp. 100 degrees too cold

  • Customer: Robert from Funston GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

ovens wouldn't maintain temperature after preheat cycle

  • Customer: sherri from elk horn IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

No temperature control

  • Customer: Max from Houston TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Oven door locked and was flashing code F4

  • Customer: Mary L. from Trinity TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Replaced a broken hinge.

  • Customer: Joseph from New Windsor NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
The repair was easy. The door pulls off the hinges without any tools. I had to remove four screws ihat held the wall oven in place. I then removed approximately eight trim screws to expose the two screws holding the hinge in place.I then needed to utilize a nut driver to put the screws in the new hinges because the screws cut threads into the hinge as you put them in so they are a little tight and the nut driver makes this step easier.

BAKE ELEMENT BURNED

  • Customer: Manuk from STUDIO CITY CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Turn off the electricity for the oven from the switch box. Unsure the damaged element from the unit. Pull it forward and unplug connections. Then plug the new element and use the new screws to screw it back to the unit. That's all

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Lower element in top double oven failed

  • Customer: Keith from hixson TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
turned off power, removed two screws mounting the old element, cut wires, and removed old element, crimped new stake connectors onto existing wiring, attached stake connectors to new element, installed element with two new screws provided, turned power back on.
It would be easier to just slip the two stake connectors off and reinstall on the new element but I elected to install new connectors because the oven was over ten years old and one seemed loose.

needed a rack for my oven

  • Customer: steve from herald CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
i needed a rack for my oven i looked everywhere for one that fit could not find one.my oven is not common due to the fact it is for a very small space and only 18 " wide i stumbled on this site by accident and decided to try it out shipping was very fast and people there are very nice any have alot of knoldge about parts it is very well set up to order with just a modle # i have told my whole familey about this site they did a great job and i will be back for more parts.

Lower heating element not working

  • Customer: John from Pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I removed the two screws that held in the old part. I pulled the element out a few inches.I disconnected two wires from the old element and connected it to the new. Using the screws provided I reconnected the unit. All went well. No need for repairman. 1

Oven Temperature was 50 degrees low

  • Customer: Eugene from Clinton IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

F1-1 and F3-1 error code

  • Customer: Barbara from Lakeville MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

A seal came off the oven

  • Customer: andrea from new york NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I found the model, ordered the new seal, it arrived very quickly via mail and I replaced the seal. You simply slid off the old, slid on the new one and hooked it in place. No expensive repairman!
All Instructions for the CWE5800ACB
31-45 of 144