Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CW3303L

CW3303L (P1128412W) Amana Washer - Overview

Get Parts and Repair Help for CW3303L

If you know the washer repair part you need, you can browse the list of all parts on the CW3303L, or you can search by name or part description. You can also find your part by where it is located on the CW3303L by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CW3303L parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below....

Order within the next 4 hrs and your part ships today!
$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

Order within the next 4 hrs and your part ships today!
$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has s...

Order within the next 4 hrs and your part ships today!
$3.02

Lid Hinge Mounting Screw

Sold individually.

Order within the next 4 hrs and your part ships today!
$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrat...

Order within the next 4 hrs and your part ships today!
$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Order within the next 4 hrs and your part ships today!
$2.98

Screw

Sold Individually.

Order within the next 4 hrs and your part ships today!
$16.17

V-Style Drive Belt (32.5 inches long)

This v-style drive belt is thirty-two and a half inches long and half of an inch wide.

Order within the next 4 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 4 hrs and your part ships today!
$5.20

Rubber Foot Pad

This foot pad is just over an inch in diameter. It is all black in color and is made entirely of rubber. This pad is used for the levelling legs of many washing machines.

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Frayed V-belt

  • Customer: John from Milton, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 47 of 53 people found this instruction helpful
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, remove 4 mounting bra... read more

The Seal On The Bottom Of The Tub Was Leaking

  • Customer: HOWARD from CORTLAND, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 31 of 39 people found this instruction helpful
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty much straight forwar... read more

tub leaking water

  • Customer: Raymond from East Sandwich, MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set, Wrench set
  • 17 of 20 people found this instruction helpful
Took off the agitator, removed inner tub, exposing the hub drive. Found fusion between hub drive and agitator shaft. Rather than using a wheel puller as instructions recommended I got my masonry hammer and removed the drive hub in pieces. Removed debris from the tub. Installed sealant around lower seal as instructed. Re-assembled inner tub, agitator with... read more