Models > CVGX2423B > Instructions

CVGX2423B Jenn-Air Cooktop - Instructions

All installation instructions for CVGX2423B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CVGX2423B
16-30 of 31
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I knocked the knob off the fan control and the stem of the control broke, too.

  • Customer: Carolyn from Cressey CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
First I removed 3 screws that held a plate againt the wires. Then pulled the element out about 3 inches and disconnected the 2 wires holding the old element and connected them to the new element. Replaced the plate with 3 screws and I was done.

the spark igniters would continue to spark after the burners were lit

  • Customer: Robert from White Rock NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Since the problem would only occur when the right front burner was on, I first replaced the ignitor, but the problem persisted. To replace the spark module I had to pull the range out of the nook it is in in the counter top. Then (after ensuring that the power was off) I removed the back cover. The spark module was easily located and removing two screws and disconnecting a few wires liberated it. The new one went in easily since it is the same part number and an exact match. Put the back on and check that the problem was solved. Done!

Scratched up grill on stove top

  • Customer: Tracy from Albany GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Just needed to replace a scratched up grill on my stove top. The black paint was scratched off and looked horrible. You site made it very easy to find what I needed and it got here in two days. If I had known it was going to be that quick and easy, I would've done it a long time ago! Thanks!

fan wouldn't turn off

  • Customer: Conrad from Roswell GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 1 people found this instruction helpful
Removed the part that didn't work and replaced it with the new one

Bashed Air Grill

  • Customer: Daniel from Mullica Hill NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Took the old one out, plopped the new one in.

Worn control panel due to age and use.

  • Customer: T.J. from Corona CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Ordered necessary parts from PartSelect and upon arrival removed old parts and installed new parts. Functionality was not changed, but the appearance improvement was fantastic. Now I can be proud of my kitchen appliances and how they appear to guests in my home. The best aspect of my experience was the ease of accessing and using the PartSelect web-site and the exploded schematic(s) that made part identification and order placement a breeze.

Regards, T.j. Brandt Corona, CA

would not light

  • Customer: ned from leland MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 3 people found this instruction helpful
remove two screws then unplug the wires put the wires back on the new one

replacement filter for jenn-aire

  • Customer: Fred from Mount Sinai NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the filter fit because the scale in the photo allowed me to choose which one to buy!

Nasty, clogged, old grease filter

  • Customer: Kim from Cottontown TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)

Continuous clicking

  • Customer: Matthew from Marengo IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The aluminum threads on the post (part15) can get stripped very easily. If you cannot tighten down the flat nut the clicking will occur.

The fan switch on the Jenn-Air downdraft cooktop was bad and needed to be replaced

  • Customer: ALAN from Encinitas CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Be sure to unplug the unit first. Removing the screws to the control panel, disconnecting the wires, and replacing the switch is the easy part. The threads are plastic where the nut holds the switch in place, and it would not stay tight, but popped loose because of the plastic threads. I added some super glue to the threads and hand tightened. Replace control panel cover, re-plug into outlet.

Igniter switch was inop

  • Customer: Mark from Kingwood TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It took longer to figure out how to get the selector cover off than it did to replace the switch. Once I had access it was only about a 10-15 minute job to install and put it all back together and operative. Actually a very easy job to do.

THE IGNITERS WOULD SPARK CONTINUALLY AND THEN ONE BURNER WOULD NOT GO ON

  • Customer: Diann from Wylie TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
TURNED OFF GAS, UNSCREWED NUT THAT HELD ON THE PLATE UNPLUGGED THE IGNITER AND REPLACED IT AND PUT IT BACK TOGETHER, VERY EASY FIX.

bad screw on cap

  • Customer: Herbert from Awendaw SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replace burner cap

Our old grease filter was molding

  • Customer: Kathy from Gurnee IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the old filter out and put a new one in. No tools no fuss no muss. Very easy.
All Instructions for the CVGX2423B
16-30 of 31