Models > CVG4280W > Instructions

CVG4280W Jenn-Air Cooktop - Instructions

All installation instructions for CVG4280W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CVG4280W
46-52 of 52
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replacing old parts

  • Customer: Debra from Carlstadt NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
wanted a fresh clean look on the burners since they were old and getting dirty and blackened from use. Easy to replace with new one.

Old and stained

  • Customer: Susan from South Lake Tahoe CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair was extremely easy. My stove still worked but looked awful. By changing out these parts it makes it look brand new.Thank you.

Burners would not light - rusted

  • Customer: Bob from Mansfield TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
New front burners fit well, but back ones had just enough variance in tne angle of the gas-supply tube that it would not fit the mounting bracket holding both burners in place. I had to grind a small flange off of the bracket so the gas tube would clear. Once that was done the burners worked well.

Old burners

  • Customer: Alan from Scappoose OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The issue: the burners were abused by the previous tenant, the burnt grease was clearly visible. They would hardly ignite and the smell of gas was always present.The remedy: new burners. They were hard to find, I was not completely sure about to stove model (it could be quite a search to find the right ones). There is a front burner and a back one. I was not sure from the diagram about the back one, so I called Partselect and someone answered the call right-away. The burners arrived a few days later, and they were the correct ones. The burners are not Jenn-air specific, it looks like several brand names use the same ones. The installation was extremely easy, a few hex screws. The stove is like new. I highly recommend Partselect.

The original filter was decomposing each time I washed it

  • Customer: Sharon from Kenai AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

Filter worn out, exhasut fan kept going off

  • Customer: John from Cayce SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

How to disassemble the tower from the bottom rack and then reinstall

  • Customer: Faye from Cuero TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After struggling with getting the tower off the rack. We needed to look up how to install on the Internet. It amounted to just turning it clockwise until it locked in place. I felt silly as it was easy once I knew what to do. Instructions in box would have been helpful.
All Instructions for the CVG4280W
46-52 of 52