CVG2420W Jenn-Air Cooktop - Instructions

After I bought this part, installed it and the clicking still did not stop I finally found the problem. If your ignitor can still click then it's still good. The problem is the electric connection between the head burners and the base burners (Top Assembly diagram). Put a little weight on the head burner while grabbing it with your hand and grind it into the base burner with a little twisting motion. Repeat for all 4 burners. Presto! (you could be more professional and use steel wool or sandpaper to.)
If you stll want to know how to install this part begin by removing the control panel bracket #24. Then remove the glass top w/seal #9 (after removing the knobs). You may have to tease this out because the rubber seal is sticky. The switch plate #14 comes off after removing 2 obvious screws at each end and 2 not-so-obvious star screws attaching it to the manifold #6. Remove the spark module by removing 2 of the 3 screws and sliding it out of the 3rd screw.

Lift off blower vent cover. Lift out old filter. Clean walls and bottom of down draft using degrease soap and warm water. Dry. Discovered my grease filter will not install diagonally as shown in unit manual. Decided to drop into downdraft and put in front of fan suction. Found this left a gap at the top of fan suction that was not covered by the filter. Cut piece of wood 1 inch thick and width and length to drop down in the downdraft and lay on bottom. Set filter on top of wood in front of the fan suction. Verified that fan suction would pull filter tight against the opening by turning fan on and off. Put vent cover back over downdraft and told wife I was done.

I removed the center vent and inserted the filter...easy as pie...I went to your website and everything was there in an easy to follow way that even I could understand, my husband was totally impressed that I took care of it on my own....silly man.....it was so easy and delivery was extremely quick....so simple....thank you for making it so!!!!

Replaced the filter which required no tools.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

Replacement was slightly bigger than the small burners and slightly smaller than the large burners. It looks OK and we moved it to a burner that we don't use very often.

Ordered a replacement grease filter.

I merely lifted the downdraft cover and inserted the new screen as
directed. THANK YOU FOR YOUR PROMPT RESPONSE TO MY ORDER.

Just placed new filter in slot

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

very easy slip in

Took the old filter out and put a new one in. No tools no fuss no muss. Very easy.

The old grease filter was removed and the entire downdraft was cleaned. The new filter was slipped in. It is so nice to have the old one out. I am so appreciative of finding this part. :-)

the filter fit because the scale in the photo allowed me to choose which one to buy!

Pull the knobs, undo the torx nuts, fish out the ones I dropped into the cooktop; pull the panel to reveal the igniter module; undo the three nuts holding it - then transfer the wires one-by-one to the new module; fish out the screws with the magnet; secure the new igniter; replace the panels; redo the torx nuts; fish out the once I drop (AGAIN) and we're good to go. I was almost out of matches. The most useful tool was the magnet on a stick - my fingers are too big for the spaces I had to get into. Anyone can do this, and it saves money...