CVE407B-C Jenn-Air Cooktop - Instructions

Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.

Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.

Broke both crimp on washers. Drilled two appropriate holes in a dowell rod, used these holes to hold the new crimp on washers. Then drove the washers onto the switch's built in pegs.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions

Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

Disconnect power cord first. I remove the air fan cover to get to the two screws which hold the fan switch and burner knobs. Remove burner knobs and and remove switch cover, disconnect wires to fan switch. Pry spring nuts off with screwdriver to get switch off. Pay attention to which way switch goes on so that it turns on in the right direction. Install spring nuts (they may look too small but they're not) using a deep small socket the size of the spring nuts tap the the socket with a small hammer and the nuts will be locked in place. Put everything back in place and your done.

First the power to the cooktop was turned off. Two screws were removed to be able to lift the fan switch holder. The old switch was removed easly because it fell apart. The nuts holding the part in broke as they were removed so they could not be reused. The new switch was put in place however the nuts were too small. I don't know what they were supposed to fit but not these screws. The part was super glued in place. It works perfectly.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Pulled the old one out & inserted the new one. Less than five minutes.

Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.

We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

Remove and replace grease filter.