Models > CVE3400B > Instructions

CVE3400B Jenn-Air Cooktop - Instructions

All installation instructions for CVE3400B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CVE3400B
1-15 of 55
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Outer element of dual element burner didn't work

  • Customer: Michael from Collierville TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 78 of 105 people found this instruction helpful
Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.

Attach the orange wire (old switch terminal 5) to S2
Attach the yellow wire (old switch terminal 4) to 4a
Attach the tan/(white?) wire (old switch terminal 3) to terminal 4 on the new switch
Attach the single red wire from the right front element to terminal 2 on the new switch.
Attach the 'compound' red wires (the ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.
There is no need to seperate the compound red wires as the instructions might lead you to believe.
Good Luck

Outer Ring of Dual Radiant Burner Does Not Come On

  • Customer: Christopher from Fredericksburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 22 of 32 people found this instruction helpful
Undid two screws on underside of cook top, lifted and exposed underside. Transferred wires from the faulty burner to the new burner, one at a time, paying close attention to their respective position on the wiring posts/terminals. Undid two screws holding old burner and then mounted the new burner to underside of cook top. Was really simple to do. :)

replaced heating element on flat surface stove top

  • Customer: dennis from assonet MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 20 of 28 people found this instruction helpful
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.

The repair itself was very easy. “How to connect” was very hard to get.

  • Customer: Igor from Campbell CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 14 of 19 people found this instruction helpful
The repair itself was very easy. “How to connect” was very hard to get.


To get access to the switch, unscrew 2 screws from each side of front panel and then 4 screws from the bottom of it (open the door first). Have a box or a small table about 30” high to use it as support for the front panel.

The end result (colors for the Right Front- R.F.- burner) : Old label -> New label

1. Double RED: N -> P2 (incoming power, Line 1)
2. Single RED: N -> 2 (to Inner AND Outer heating elements common wire)
3. Single BLK: L1 -> P1 (incoming power, Line 2)
4. Single TAN: H1 -> 4 (to the Inner heating element)
5. Single YEL: H2-> 4a (to the Inner heating element)
6. Single BLK: P -> S2 (to the R.F. indicator control light)
7. Attach jumper black wire (included with new switch) from P1 (P1 has two connectors close together) to S1.

Done.

Element did not heat

  • Customer: Michael from Lancaster PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 26 people found this instruction helpful
Removed stove top. Removed old element paying attention to wiring connections. Installed new element. Redconnected wiring. Put stove top back in place. Tested. Ate dinner.

old switch had shorted and burned out

  • Customer: Larry from Hampton Cove AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 14 of 20 people found this instruction helpful
This was a range top. i removed the 12 hex machine scews holding on the top, then removed the two star screws holding the old switch. there were fore wire that had fitted on tabs. Hooked them to the new swtch and reassembeld. Easy repair since i could lift the unit out without disconnecting main cables. Replacement range would have been oveer $1000. Psrt was under $40 and delivered in a matter of days.

Jenn Air Dual element switch broke

  • Customer: Todd from Concord OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 10 of 12 people found this instruction helpful
This is not at hard as it seems; I followed the first guy's story and ignored the colors because mine were different. I did have to split the combined red wires, intimidating at first but once I split them it was down hill.
I did have to use the jumper wire.

Follow
Appliance Repaired: Jenn-Air Range/Stove/Oven/Hood

Model: cve3401b

Age Of Appliance: 5 - 10 years


Remove Ceran Galss top by removing hex screws below the rim. Also remove the two opposing screws in the center of the downdraft opening. Ceran top comes off easily now.
The instructions with the new switch were very poorly written, so here is how I got the new switch to work:
Attach the black wire(s) from the old switch (terminal 2) to the new switch terminal P1. Also attach the jumper cable to P1 and "jump" it to S1.

Attach the wire from old switch terminal 5)to S2
Attach the wire from old switch terminal 4 to 4a
Attach the wire from old switch terminal 3 to terminal 4 on the new switch
Detach the 'compound' red wires from each other.
(The ones that come from the left rear/outlet connection and is also attached to the right rear switch) to terminal P2 on the new switch.

I attached common female connectors.
Attach the newly split single red wire from the right front element to terminal 2 on the new switch.

One note:

Before you remove the four screws that hold the four swtiches down make sure that you use a sharpie and mark the switchbox location. You will notice that it is difficult to get them to line up again with the holes in the cooktop.

Thanks partselect.com!

Knob stem broke off at the base near the switch

  • Customer: Samuel from San Antonio TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 13 of 23 people found this instruction helpful
Removed stove top from the counter. Removed the glass frame and glass from the top. Removed the broken switch. Replaced with the new switch. Reassembled the unit and replaced it in the counter top.

One problem is the switch only fits in the space one way because of the first burner light. When installed the only way the knob fits on the switch stem makes the dot on the knob backwards. It now shows to be on medium speed when it is off.

Filter was starting to come apart from frequent cleaning.

  • Customer: Mary H. from Appleton WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
I removed the center vent and inserted the filter...easy as pie...I went to your website and everything was there in an easy to follow way that even I could understand, my husband was totally impressed that I took care of it on my own....silly man.....it was so easy and delivery was extremely quick....so simple....thank you for making it so!!!!

SMALL ELEMENT ON COUNTER TOP RANGE NOT HEATING.

  • Customer: Brian E from Waldorf MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
1. TURNED OFF POWER TO TROUBLE SHOOT THE COUNTER TOP RANGE ELEMENTS.
2.RAISED THE COUNTER TOP UP TO WORK ON IT AND SLID TWO EVENLY PLACED WOODEN SLATS UNDER THE BOTTOM OF THE HOUSFOR STABILITY SO IT WOULD NOT FALL BACKDOWN INTO THE COUNTER TOP CUT-OUT.
3. WITH A 1/4" NUT DRIVER REMOVED THE 10 HEX-HEAD SCREW THAT WERE HOLDING THE BLACK GLASS TOP IN PLACE, PULLED OFF THE 4 .CONTROL KNOBS AND CAREFULLY REMOVED THE GLASS COVER AND CAREFULLY SEET IT ASIDE IN A SAFE PLACE.
5. A VISUAL INSPECTION OF THE NON WORKING ELEMENT SHOWED THAT IT HAD A BURN OUT SPOT CAUSING IT NOT TO HEAT.
6. GOT THE MODEL NUMBER OF THE APPLIANCE AND CHECKED THE INTERNET FOR PARTS SUPPLIERS, CHOSE PARTS ELECT BECAUSE THEY HAD THE PART IN STOCK AND COULD OVERNIGHT IT FOR REINSTALLATION THE NEXT DAY, PART DID ARRIVE THE NEXT MORNING. A VISUAL INSPECTION SHOW THAT IT WAS THE CORRECT PART AND IT WOULD BE A LIKE FOR LIKE SWAP OUT.
7. PRIOR TO REPLACING THE ELEMENT CHECK TO SEE THAT THE ELECTRICAL POWER WAS STILL OFF AT THE CIRCUIT BREAKER, MADE A QUICK SKETCH OF THE WIRING AND IDENTIFIED THE WIRES SO THAT THEY WOULD BE RETERMINATED AT THE SAME POINTS.
8.USING THE NEEDLE NOSE PLIERS PULLED OFF THE 4 STAKE ON TERMINATIONS.
9. LIFTED OUT THE 6" FROM THE BODY OF THE UNIT , REMOVED THE 4 PHILLIPS SCREWS HOLDING PARTS WHAT WERE TO BE TRANSFERED ONTO THE NEW ELEMENT.
10. TRANSFERED PARTS ONTO THE NEW ELEMENT, REINSTALLED THE ELEMENT INTO THE BODY OF THE UNIT, REINSTALLED THE 4-STAKE-ON WIRES TO THERE APPROPRIATE TERMINALS AND VERIFIED WITH PREVIOUS WIRING SKETCH.
11. REINSTALLED THE GLASS TOP, 10 SCREW HOLDING IT IN PLACE AND THE 4-CONTROL KNOBS.
12 .TURNED MAIN POWER TO THE UNIT BACK ON AND TURNED ON THE REPLACED ELEMENT, IT WORK CORRECTLY, ALSO CHECKED THE OTHER 3 ELEMENTS TO MAKE SURE THAT THEY WERE WORKING CORRECTLY.
13. WHEN THE UNIT HAD COOLED, REMOVED THE WOODEN SLATS AND LOWERED THE COUNTER TOP BACK INTO ITS CUT-OUT MAKING SURE NOT TO DAMAGE THE GLASSTOP.
JOB COMPLETE.

the left front burner burned out & none of the lights to show if a burner was hot would come on.

  • Customer: Richard from Fair oaks Ranch TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

Worn grease filter

  • Customer: Louise from Birmingham AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 11 people found this instruction helpful
Replaced the filter which required no tools.

Fan switch only fits in one way and makes knob point to medium setting when off. The switch did not come with a mounting nut and the original in Jenn-Air didnt match.

  • Customer: Gregory from Prospect CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 15 people found this instruction helpful
Lifted cooktop out of cabinet, removed flange around glass cooktop, remove glass and access the fan swicth. I used teflon tape to get original mounting nut to stay tight on the plastic fan switch.

Replace Grease Filter For Downdraft Stove Top

  • Customer: Johnnie from Daphne AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
Lift off blower vent cover. Lift out old filter. Clean walls and bottom of down draft using degrease soap and warm water. Dry. Discovered my grease filter will not install diagonally as shown in unit manual. Decided to drop into downdraft and put in front of fan suction. Found this left a gap at the top of fan suction that was not covered by the filter. Cut piece of wood 1 inch thick and width and length to drop down in the downdraft and lay on bottom. Set filter on top of wood in front of the fan suction. Verified that fan suction would pull filter tight against the opening by turning fan on and off. Put vent cover back over downdraft and told wife I was done.

Plastic knob broke for the second time since cooktop was installed.

  • Customer: Joseph R. from Greenville SC
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
The entire cooktop had to be removed and taken apart to replace fan switch. I am thankful that this replacement part was available (slightly different than original part) through PartSelect.com since my local appliance parts store told me the part was no longer available.
All Instructions for the CVE3400B
1-15 of 55