Models > CTF1924ARA

CTF1924ARA Magic Chef Refrigerator - Overview

Get Parts and Repair Help for CTF1924ARA

If you know the refrigerator repair part you need, you can browse the list of all parts on the CTF1924ARA, or you can search by name or part description. You can also find your part by where it is located on the CTF1924ARA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for CTF1924ARA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$104.13

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

Order within the next 11 hrs and your part ships today!
$8.64

Shelf Retainer Bar End Cap

Sold individually.

Order within the next 11 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 11 hrs and your part ships today!
$37.79

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

Order within the next 11 hrs and your part ships today!
$4.39

Crisper Drawer Shelf Support

This crisper drawer shelf support is used for many refrigerators.

Order within the next 11 hrs and your part ships today!
$8.59

Light Rocker Switch

This light switch is triggered by the door opening and closing.

Order within the next 11 hrs and your part ships today!
$15.21

Water Fill Cup and Bearing

Order within the next 11 hrs and your part ships today!
$2.07

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

Order within the next 11 hrs and your part ships today!
$4.70

Compression Nut

This compression nut is used with the plastic water line of the icemaker assembly.

Order within the next 11 hrs and your part ships today!
$40.68

Lower Door Shelf Trim

This refrigerator door shelf trim is 21 inches long. It is all white in color, and it is made entirely of metal.

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 573 of 590 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 216 of 287 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 97 of 104 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more