Models > CTF1920ARW > Instructions

CTF1920ARW Magic Chef Refrigerator - Instructions

All installation instructions for CTF1920ARW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CTF1920ARW
76-90 of 505
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The ice stripper cracked from freezing.

  • Customer: David from Discovery Bay CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 6 people found this instruction helpful
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Condenser Fan Failure

  • Customer: Al from Tonka Bay MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 2 of 3 people found this instruction helpful
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!

Quit making ice

  • Customer: James from Charleston SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

thermostat not working

  • Customer: Amy from Pleasant Grove UT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Ok, first off, I am a girl-with absolutely no 'fix it skills" whatsover. My husband had pointed out the problem to me the second time the fridge started to get warm. I ordered the part (wrong one first time), then reordered the correct part. I emptied the freezer, defrosted the coils, installed the part. Put back together-all of it took about 15 minutes. I am still oh so very proud of myself.

Broken cup water fill on ice maker

  • Customer: Matthew from Aurora CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Condenser fan making noise

  • Customer: Richard from North Easton MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 2 of 3 people found this instruction helpful
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Condenser Fan Motor seized up

  • Customer: Peter from Herndon VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

Old Ice Maker failed

  • Customer: John from Gurnee IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
I removed the old ice maker and during the short disassembly noticed a burned out connection to the heater element that allows the ice to be broken free of the tray and dumped into the bin. Part Select had a new unit to me next day! I had watched their short install video, and read some of the user comments, already. Re-installing the new unit was a snap, and just as the video had described except for the mount bracket. The only thing that concerned me was that the new unit did not immediately do anything. I began to investigate and found that the flexible water "chute" connection had ice in it! I unplugged the refer, unscrewed the water filter and drained it. I disconnected the water feed on the outside back of the unit as well to make sure water could flow easily to the ice maker port. I filled the water filter with boiling hot water and replaced it, I plugged in the refer, and reprogrammed the date and time. Several hours later I checked the ice maker and it was -- making ice!

install new icemaker

  • Customer: Nancy from Englewood FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
First had to remove baskets and door from freezer. Removed three screws; removed old ice maker; Attached new ice maker with three screws; removed arm from old ice maker and placed in the new ice maker. Replaced door and baskets

need better space

  • Customer: Mabel from Newington CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I ordered a freezer shelf to add a shelf. Tried to install when arrived only to discover that the 2 brackets were needed and I didn't know. Once I ordered the brackets it was a breeze to set it up . Nice to have things so I can actually see the items not being pilled on top of each other. Hopefully will not lose food.

water leaking into ice tray, frozen glob of ice

  • Customer: james from newfield NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

Ice Maker stopped working

  • Customer: Tami from Apple Valley CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Replacing the ice maker was the easy part, next morning still no ice so called repairman, replaced fuse in wiring harness, next morning still no ice, called repairman again to find out that thermostat in brand new ice maker is bad, had to reuse old thermostat to make new ice maker work so could not return it to partselect.com. New ice maker cost $108 and repairman $90, expensive lesson learned.

ice maker quit working

  • Customer: Ted from Aurora NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Since it was an older appliance I decided to replace the whole ice maker assembly. I carefully disassembled the old one and then installed the new one. piece of cake.

Ice maker putting black pieces of plastic in the ice

  • Customer: Doug from Lewisville TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.

Ice maker not making ice

  • Customer: sandra from Scottsdale AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 1 of 1 people found this instruction helpful
Repair done according to video and instructions. What you need to know is myself and my husband are adverse to all kinds of "simple" repairs because they never go well and we are not handyman kind of persons. This, I must say, was a delightful change in our typical experience of attempting to make our own repairs.
Thanks
Sandy
All Instructions for the CTF1920ARW
76-90 of 505