Models > CTB1922ARW > Instructions

CTB1922ARW Magic Chef Refrigerator - Instructions

All installation instructions for CTB1922ARW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CTB1922ARW
391-405 of 505
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker was leaking into the cube tray

  • Customer: Richard from South Lyon MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Once I received the new icemaker, I removed the old one by loosening the two upper screws and removing the lower. The wire connector came out easily. The wire and the bale from the old unit had to be transferred to the new unit. Then the new unit was reinstalled and the wire plugged back in. It took several hours for the cubes to begin dropping.

broken crisper drawer mount

  • Customer: lloyd from california KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old mount with allen wrench replaced with new mount

ice maker stopped making ice

  • Customer: George from Winhall VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Partselect was great, but I "Gilligan-ed" on the fix changing both the icemaker AND water feed solenoid, BEFORE determining the white rubber water feeder tube that installs from back of fridge and feeds ice maker tray inside of freezer was frozen/ blocked. Make sure you check this FIRST, by proding a screw driver up the tube inside freezer and/ or pulling feeder tube out from back of fridge. If the blockage is substantial enough, it will make removal difficult until melts and tube contracts. Good luck!!

light switch sticking

  • Customer: Paula from Rush NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

Light did not come on (bad bulb!) on TC18KL

  • Customer: Louis from Beloit WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

not made ice

  • Customer: Sunny from RICHARDSON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

Ice maker not making ice

  • Customer: Warren from Houma LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

Not making ice

  • Customer: Raymond from Hanover Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

Ice maker quit

  • Customer: Peter from Johannesburg MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

Ice maker leaked a little, then quit completely.

  • Customer: Steve from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

Ice maker water level was overflowing.

  • Customer: Brian R from Rockwall TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I followed the repair instructions the Part Select site provided for this replacement valve. The only differences were I needed a small socket/wrench set in place of screw drivers.

the ice maker stopped working

  • Customer: Patrick from Barnegat NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Broken End Cap

  • Customer: michael from Hoffman Estates IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply replaced part. Press fit shelf retaining bar back into place. I was just glad you had this obscure part which was easy to find on you website.

Ice maker drips water, making a blob of ice in the compartment

  • Customer: Charles from Metairie LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

Old ice maker element burnt out

  • Customer: David from Bonita CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins
All Instructions for the CTB1922ARW
391-405 of 505