Models > CTB1921ARW > Instructions

CTB1921ARW Magic Chef Refrigerator - Instructions

All installation instructions for CTB1921ARW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CTB1921ARW
451-465 of 490
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fan motor stopped working

  • Customer: john from white pine TN
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

ice maker stopped making ice

  • Customer: David from Jacksonville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

Ice Maker was not functioning

  • Customer: BRET from SAN DIEGO CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

Refrigerator not shutting off, liquids freezing in fridge

  • Customer: Barbara from Apollo PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

light wouldn't go on

  • Customer: William from Leesburg FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Leaking water

  • Customer: Terry L. from Glasgow KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Ice maker not working

  • Customer: Charles from Middletown OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed on line instructions. Instructions were very helpful. The part was an exact replacement. Everything went as planned.

Was Not Making Ice

  • Customer: Don from Desert Hot Springs CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the Video, and it went almost as the video, except for the rails for the ice tub, so instead of the nut driver, had to use an open end 1/4" wrench. Now its a working with lots a ice....

ICEMAKER

  • Customer: BETTY from HOCKLEY TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I RECEIVED THE NEW ICEMAKER THE NEXT DAY AFTER I HAD ORDERED IT.AFTER WATCHING THE VIDEO ON HOW TO INSTALL THE ICEMAKER I INSTALLED IT WITHIN A FEW MINUTES WHICH I REALLY SURPRISED MYSELF SINCE THIS WAS MY FIRST REPAIR JOB TO DO BY MYSELF.THE NEW ICE MAKER HAS BEEN WORKING GREAT AND I AM VERY PLEASED WITH PARTSELECT AND WILL CONTINUE TO CONTACT YOU WHEN I AM IN NEED OF ANY PARTS. THANK YOU, BETTY

dripping and making globs of ice

  • Customer: Edward from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Ice Maker stops working..

  • Customer: Tony from Litchfield Park AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.

Ice maker tray in side by side leaked and created large lumps of ice

  • Customer: Catherine from Punta Gorda FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Stopped making ice, leaking water into freezer to kitchen floor!

  • Customer: John from Seabrook NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

door trim bent and ugly

  • Customer: douglas from surprise AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just removed old trim and attached new trim by hand. good results. Happy with your product and tmeliness of delivery Thanks Doug Salter

The icemaker was leaking into the ice hopper creating an iceberg.

  • Customer: Peter from Hemet CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After receiving the new ice maker assembly I placed the new part next to the old one to see what I needed to transfer from the old to the new. After removing the wiring harness and a few small parts, I placed them on the new assembly. After that it was a snap which timewise took about 15 minutes. I am pleased to say the ice hopper is full and being replenished very efficiently.
All Instructions for the CTB1921ARW
451-465 of 490