CTB1502ARW Magic Chef Refrigerator - Instructions

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

I just took the doors off my fridge with a socket set and replaced the broken piece. It was a piece of cake.

This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a guide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.

Thanks...Ron Norwood

, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.

Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.

Found evaporator fan blade not attached to motor, it's hub was cracked. My wife wanted to buy a new fridge and I fixed it for $7 in parts. Removed freezer shelf, unscrewed and removed back panel, uncliped fan cover from back panel, replaced blade and reassembled.

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

removed the cover from the back of the refrigerator, and used the nutdriver to loosen screw on the single outlet water valve, removed the old water valve and the hoses to it. Connected the hoses to the new valve and attached to the wall of the refrigerator by tightening the screw. Then removed the old ice maker from the inside of the refrigerator, by loosening the two screws and attached the new one, I tightened the screws and then I was done. It is working great.

Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!

Watched the video, big help.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.