CSX27DRSAAD Hotpoint Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Parts Used:
-
Bob from JASPER, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker very slow and arm that controls amount of ice sticking and quit making ice
took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord
Parts Used:
-
Grimes from Bartlett, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Parts Used:
-
Patricia from Sylva, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The ice maker did not make any ice cubes
I pulled the Refrig out of the space so that I could get to the plug and water shut off. After unplugging and turning the water off, I had to remove the 7 screws holding the cardboard cover over the bottom portion of the Refrig. I then had to unloosen the water input to the the valve. Then I removed the screw holding the Water Valve. I then had to unplug the unit from the electrical connectors. After that I had to cut the plastic hoses off the valve. All that was left was to reconnect everything, replace the cardboard covering and do an operational test. Everything worked. The ice maker began to produce ice cubes and there were no leaks.
Parts Used:
-
Robert Mc from Citrus Heights, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Fridge and Freezer not cold enough
Removed everything from freezer, Removed back panel, defrosted coils. removed thermostat top left, cut wires and used heat shrink to splice back together, clipped thermostat back on. I actually replaced the defrost timer and defrost heater also. Best bet is to do all 3 at one time. Part Select will have the new parts to you in days. Great Service and the online repair man is great. I saved hundreds of dollars doing myself.
Parts Used:
-
Keith from West Palm Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice machine flapper door solenoid burned up
Follow PartSelect video on website, had no problems learned a lot
Parts Used:
-
Troy from Tullahoma, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not "dump" ice cubes
I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.
Parts Used:
-
Phayo from Lake Charles, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
summer cottage lost heat during winter inlet valve for icemaker froze
parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>
Parts Used:
-
Robert from Waterford, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Parts Used:
-
Steve from Canyon Country, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bad fan motor
-
theodore from salisbury, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker leeking
-
Wes from Marion, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Both cams (upper and lower) broken
The part came within 3 days. But it was only one cam. Part was described assembly so i thought it had both cams. I ordered the upper cam which attached to the door bottom. When I matched the new to the old --they were different. They looked the same until you put them side by side. Being the mechanic I am, I cut the rivet holding the assembly cam and pop riveted it to the old assembly. It was not difficult but annoying as I had the correct model (I have the original use and care guide book). I must commend PartSelect for their promptness.
Parts Used:
-
Louis from Cortland, NY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Parts Used:
-
Frank from Temecula, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Put the part in and observed water leaking from the ice maker which caused the cup to break
Ordered new Ice Maker from you and fixed the problem completely.
Parts Used:
-
John from Ravenden, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no ice
-
Richard from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!