CSX27CLN Hotpoint Refrigerator - Instructions

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

I noticed water leaking from the bottom right rear of the fridge. I figured it was from the ice maker feed as I don't have the ice water feature on this GE profile. I shut the water supply off, ordered the part and received it in a few days. The defective part was easily accessible after I removed the cardboard cover. I removed the copper feed and unscrewed the old valve with a nutdriver. The new part fit perfectly, and even though there were instructions in the part to use the old bracket. the plastic water feed fit into the ice maker compression fitting with ease. I ran into a problem when I re-installed the copper compression fitting on the new valve,as I could not stop a leak from the top of the compression fitting. When my plumber originally installed the copper line he used enough pressure to deform the compression sleeve that slips over the copper tube. I had a couple of them in my "parts" drawer, so I took my tubing cutter and took 1/2" of the end of the copper supply line; slipped the new sleeve and re-installed the compression nut over the valve....fit perfectly. Turned on the water supply; no leaks. Checked the icemaker about 4 hours later and it made the first tray of ice. If I didn't have to deal with the water supply leak at the fitting, the job would have been finished in 30 to 45 minutes.

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.

The longest part was emptying the door for removal. Remove screw on top of hinge, have someone hold the door while I removed the hinge bolts, unplug door from fridge, then remove the door. Then just put the cam-riser where the old one was and put the door back on. Easy as pie.

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

The replacement part came with a one page instruction sheet. Following those instructions I cut the two hoses on the old resivour and removed it. I then cut the hoses on the new resivour to desired length (all inside the refrigerator). Using the two couplers provided with the new resivour I hocked the two hoses together and tightened them with a wrench. It took longer to clean the refrigerator than it did to replace the part. Instruction sheet was very helpful

Got a new valve

Connected the 2 wires and pushed in the switch until it clicked.

remove the back cover where the valve is located, unplug the refrige, turn the water off. Remove the valve unit, cut the plastic water lines with the utility knife,unscrew the water feed. remove the unit. reasemble the new unit,install the water feed, connect by puching in the ice maker line and the water despencer line into the new unit.Plug the refrig back in and purge the water line. (done) saved a service call$$$$

per your instructions