Models > CSX22EHB > Instructions

CSX22EHB Hotpoint Refrigerator - Instructions

All installation instructions for CSX22EHB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSX22EHB
1-15 of 261
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door would not automatically close.

  • Customer: Gary from North eastham AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 90 of 98 people found this instruction helpful
Symptom: Door did not close automatically. Also had found small chunks of black plastic on the floor. Refrigerator door was slightly lower than the freezer door.

One false start because I did not realize both of the door-closing cams had disintegrated and I had only ordered the cam without the hinge.

Purchased part 290199 Hinge Assembly. It came with matching door-closing cam. (Had not known so I also purchased the cam 297995 separately). Next time I will know to only purchase the Hinge Assembly.

Replacement procedure took about 20 minutes including removing and replacing door shelves and their contents. Two people involved.

1. Remove all door shelves with contents and other contents on door.

2. Remove the top Phillips head screw holding the decorative plastic on the top.

3. Remove the two top hinge screws on top of refrigerator using metric #8 socket wrench. Second person made sure door did not fall off.

4. Lift the door off the bottom hinge pin. Second person holds door on it’s side.

5. Take off the bottom refrigerator cover

6. Remove the bottom hinge assembly screws using metric #8 socket wrench.

7. Mount the replacement bottom hinge assembly and tighten the two screws.

8. On the door bottom, remove the outer screw and loosen the inner screw using metric #8 socket wrench.

9. Replace the door-closing cam (or what is left of it) with the cam in line with the door and cam bumps away from the door.

10. Place the door back on the hinge pin (one person holds while the other person maneuvers the door bottom).

11. Replace the top hinge and reinsert the screws on top of the refrigerator. Dress the door so that it does not press hard on the rubber door gaskets (or the door will fail to shut automatically). Tighten the screws.

12. Replace the decorative plastic over the top hinge.

13. Open the door and replace the bottom refrigerator cover.

14. Replace the door shelves and all contents.

15 Close the door.

Sticking Light Switch

  • Customer: Jonathan from Lilburn GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 35 of 39 people found this instruction helpful
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.

Door would not close and seal properly

  • Customer: Kevin from Enumclaw WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 22 of 27 people found this instruction helpful
I found a little piece of the door closing cam broke off. While inspecting the door I found the bottom section of the seal cracked.

Parts were received within 3 days. Door cam was simple to replace. Door seal was a little tricky but tips on packaging helped me prepare the seal by heating in hot water. Everything went together and my 17 yr old fridge works great again.

Drawer Slide Rails were broken

  • Customer: Mikki from Tooele UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 20 people found this instruction helpful
For the past 6 months I've dreaded trying to find the parts and make the needed repairs to the slide rails. I just didn't have time to search for part numbers and drag all the tools out. I even contemplated buying a new frig. I thought I would have to find the original "Owners Manual". How stupid was I?

Within 15 minutes the model number was determined and the parts (VERY EASY to find the exact part) were ordered. They arrived within a week (in a GE wrapper). I unscrewed two parts per rail and within minutes the repairs were done. It took me a lot longer to clean and wipe down everything to make the refrigerator look like new again. I bragged to all my friends (like I was some type of engineer) and have referred this website to many of them. What a fantastic experience. I saved over $1,200 and the hassle of moving a frig in and out of the house. Glad you're in business and on the web.

Door closing cam had disentigrated over the past 12 years.

  • Customer: Randall from Ashburn VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 18 of 20 people found this instruction helpful
I read over the other posts here and went with jacking up the fridge door and setting it on (2) 2x4 studs. A nut driver was used to remove the bottom hinge. I then drilled out the rivet that held the old cam in place and then used a 3/16 rivet to secure the new cam. A rivet is not necessary as you can also use a nut and bolt to hold the cam in place. It took less time to order the part and install it than it did to drive over to the appliance parts store and pick it up. I ordered around 10 am and the part was here the next day at 2:00 (without special delivery costs). By 2:30 it was on my fridge.

Door wouldn't stay closed & was out of alignment

  • Customer: Patsy S from Ahoskie NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 16 of 18 people found this instruction helpful
Order 2 cams as recommended in other posts.
I didn't realize until the project was finished that the 2 cams fit together to tilt the door toward the refrigerator and force the door to catch.
1. Removed all items from door storage.
2. Removed top hinge cover held by single screw and top hinge plate held by two bolts.
3. Lifted up door to clear bottom hinge pin and removed door.
4. Turned door upside down and removed bottom hinge assembly held on by two bolts.
5. Replaced upper cam located on bottom of door and screwed the hinge assembly back on to bottom of door.
6. Drilled out the rivet that holds the lower cam to the bottom hinge pin.
7. Removed old lower cam and and replaced with new cam and secured to lower hinge assembly with pan head screw and nut (instead of rivet).
NOTE: The metal shim that goes between the cam riser & door was also broken, we used a small washer instead of the replacement shim.
8. Replaced door back onto lower hinge pin and secured upper hinge pin with original bolts.
9. Placed cover on upper hinge assembly and secured with original screw.
This is a project my husband and I completed together :)
Perhaps we will store lighter items on the door to lessen the chances of the cams deteriorating again.

Gasket was getting old and cracking.

  • Customer: Patricia from Albuquerque NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 17 of 22 people found this instruction helpful
I removed all the screws first, then everything pretty much came apart together -- the gasket along with the plastic shelving and the metal plates that hold it all together.
Not being that adept at home repair it took me longer than it probably should have. What took the longest was putting all the screws back, but once it was on I could tell I had done it right as the fridge was nice and cold inside, and at a lower setting. The old gasket had been letting cold air out and was also creating condensation where the gasket was coming apart. It was well worth it!

Panel hot to touch between freezer & refrigerator. Motor hot, fan not rotating.

  • Customer: Kimberly from Grandy NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 18 people found this instruction helpful
Unplugged refrigerator, removed three screws to take out part, disconnected the wires and removed bad unit. Removed fan blade from old unit and attached to the new unit. Attached wires, placed the new motor back in. Plugged it back in, within 20 minutes panel between freezer and refrigerator was cool to touch.

Noisey fan/motor (bad motor bearing ?)

  • Customer: Keith from Fort Worth TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
Removed 2 phillips head screws to remove ice maker (could have just loosened them)
Pulled fan off of shaft
Removed 2 phillips head screws on motor bracket , disconnected three motor wires & removed motor.
reversed process to install new motor & fan blade.
Space was a little tight for two hand and arms, but do-able.

Compressor overheating - Fridge not Cooling

  • Customer: CHRIS from LAGUNA NIGUEL CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 10 of 12 people found this instruction helpful
Condensor Fan not turning. I thought it would be an easy fix. I thought I could pull off the shroud and fan assy - no joy. Too many copper pipes and lots of tubing in the way. It took 90 minutes to remove and 30 minutes to install. The BIG hint here is to loosen the shoud, pull it back as far as you can and then remove the nut that holds the fan blade in place. THEN you can remove the motor. Get the new motor back into the shroud, get the blade back on and then tighten the shroud back up.

refigerator door doesn't close completely by itself

  • Customer: Robert from Turnersville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 10 people found this instruction helpful
Replaced broken riser cam set. Removed door by taking off top hinge pivot. (cap - 1 screw and hinge pivot - 2 screws). Lift door off bottom hinge pivot. Replace upper cam attached to bottom of door. Replace lower cam and hinge pivot assembly. (2 screws). Place door back onto lower hinge pivot and re install top hinge pivot to secure door. Adjust lower hinge pivot to achieve proper door height.

Refigerator door would no longer self close

  • Customer: Melvin from Philomath OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 10 people found this instruction helpful
Moved all items from door storage into refrigerator shelves. Removed top hinge cover held by single screw and top hinge plate held by two bolts. Lifted up door to clear bottom hinge pin and removed door. Covered open front of refrigerator with plastic wrap to keep cold in refrigerator with door removed. Laid door on kitchen counter top and removed bottom hinge assembly held on by two bolts. Replaced upper cam located on bottom of door and screwed the hinge assembly back on to bottom of door (helps to keep the three plates in same sequence and note the position of cam). Drilled out the rivet that holds the lower cam to the bottom hinge pin. Removed old lower cam and and replaced with new cam and secured to lower hinge assembly with pan head screw and nut (instead of rivet). Replaced door back onto lower hinge pin and secured upper hinge pin with original bolts. Placed cover on upper hinge assembly and secured with original screw. Removed plastic wrap from front of refrigerator and moved the items that originally were stored in the door back to provide weight needed for door to close properly. All done and the door works like new, and all in less than 45 minutes. Would have been a more difficult job without the pioneering of people on this site. Thanks to all!

bad light socket

  • Customer: nancy from silsbee TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 10 people found this instruction helpful
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy

Refridgerator warm, freezer warming

  • Customer: Dilver from Milton KY
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 17 people found this instruction helpful
refridgerater side warming, freezer warming
Appliance
General Electric Refrigerator

Model
TFXW20R

Level of Difficulty
Really easy

Time to do repair
1- 2 hours

Age of Appliance
More than 10 years

Tools
Pliers
Nutdriver
Screw drivers
Dilver From Milton, KY
Dec 05, 2011
0 out of 1 people found this instruction helpful



First I diagnosed the problem being a defrost timer as the symtoms are the same as the heater elements. I installed the timer and it worked great for about a week until the frost build up on the evaporator became too much again and then the symtoms returned. I then checked the heater elements and found that both were bad PLUS two clips to the elements were corroded. I then ordered the 2 heater elements. There is more than 1 heater element. Make sure you measure the length of each and then use the graph picture with "Parts Select" on the new ones before you order. There is about a 2" in length difference. Also one comes in a kit with thermostat and wires. Wrong for me. I really wanted that unit as I needed the harness for the bad terminals but it was the wrong heaters and it also came with a new thermostat. Luckly I did not order that one but did order a new thermostat to make sure I did not have to go through this ordeal again. When the parts came I had already replaced the terminals and was ready to go when FedX came. Just make sure you check your heaters before just buying the defrost timer as it may keep you from going back to redo your repair. Just doing your home work before ordering may save you much time in your repair. "PARTS SELECT" was one day on both orders and I just ordered standard shipping. They are great to do business with.

The refrigirator light would not come on.

  • Customer: Jania from Novato CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
All Instructions for the CSX22EHB
1-15 of 261