CSX22BCBCWH Hotpoint Refrigerator - Instructions

The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00

Removed top hinge, lifted door from bottom post. Removed post with nut driver/socket, removed corresponding bracket/receiver from door. Attached new parts to refrigerator base and bottom edge of door. Was careful to replace part pieces in the same order as original, and secured tightly. Lifted door onto bottom hinge post, leveled the door and replaced top hinge.

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

I followed the Video on your website and that made it so easy and simple to follow. Thank you!

Took back off with sockets and saw water dripping from duel inlet water valve . Turned water off and had no trouble indentifying part with partselect via computer , ordered part using ups and received in two days , followed an excelent video furnished by partselect then replaced new part with old part , turned water back on and great ! I found it a lot easyier when you have your son-in-law do the work !

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

Remove front outside cover with the pictures on it. It is held in place with 5 push type pins. Remove the ice holder or turn off the power to keep the auger from running. Remove the four screws that hold the solenoid assembly and unplug the power plug. Remove the screw and small plate that holds the flapper assembly in place. Install the new flapper and spring and re-install the other parts. My flapper was loose in the holder causing the top of the flapper to hang on the hole in the ice outlet. I installed a small screw through the back of the holder to secure the flapper.

I blocked the bottom of the door(CAREFULLY!!) in position to elevate the door & take strain off the lower hinge & pivot post, while maintaining proper door alignment. I removed the two screws holding the hinge & post assembly from the frame, saving the screws & spacer for reuse. I removed the two screws holding the upper cam bracket on the door, again keeping the attaching parts. I installed and carefully aligned the new cam, original spacer & retaining plate to the lower edge of the door. I installed the new hinge & post assembly using the existing spacer & screws. I aligned the door & seal while checking the gap from top to bottom and from side to side. I carefully tighten the screws and rechecked the gap between the door & frame as well as the alignemnt of the door seal. Once satisfied with the alignment, I finished tightening the screws. I emphasize care and extreme caution in reinstalling the screws, they are a self-tapping (self-threading) type of fastener and this requires caution to make sure they are started and installed in the original threads of the door & frame. I put them all in using only finger pressure until I was positive they were started straight, going into the original threads, NOT trying to cross-thread or cut new threads, the structure is too thin for that and stripped threads will result! The door alignment and gap spacing is critical, make sure to check these adjustments carefully to ensure proper operation. Total time of repair, less than 15 minutes. I hope I have not over-simplified this because I have over 55 years of Automotive shop experienced and an ASE Certified Master Auto & Truck Technician...:-)

Thank you for the video on how to replace defrost timer. We watched the video twice and it went rather smoothly. Thanks for your help. The frig is working like a charm.

replaced old valve with new. Might have to bend the tabs to get new valve to fit in the space where old valve was. Also plastic tubing was brittle where it was attached to valve originally so you might have to cut some off or even replace all of it. New design of attaching plastic hoses to outlet valve made installation easy. this was a snap and took about 10 minutes to complete. Was making lots of ice in no time.

unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes

Removed old slides and installed new slides.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....