CSX20LGB Hotpoint Refrigerator - Instructions

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

I watched the video online, and said, "hey, I can do that." And yep, I did. I'm pretty comfortable with handyman work - but had never tackled a frig door before. The door closing cam that had completely come apart turned out to be straight forward to fix with the replacement part.

I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.

Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.

Took door off. Replaced two cams at bottom of door, referencing those on the bottom of the freezer door. Also followed a video on the net. Worked like a jewel!

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

the door closing cam works fine.

take fan out,put new in

Empty door first then take a phillip heads screw driver and unscrewed the top hinge cover 1 screw. Then used 5/16 nut driver to loosen top hinge from fridge. remove door by lifting and then lay on table to replace the lower washer that is held in by 2 screws and you only need to loosen one all the way leaving one in to align then replace and tighten it up your done.

Followed Partselect video on how to replace cam riser. Very, very helpful!

First off, Parts Select has a great YouTube video showing exactly how to replace this refrigerator hinge cam. This repair was for my sister's 20-year old GE refrigerator. I used to do this same repair every 3 years on an expensive fridge my wife and I owned - one that had additional wood panels mounted on the door. The panels exceeded the hinges' designed weight limit, so every 3 years I replaced the bottom plastic hinge cams. On that fridge, I could replace BOTH interlocking hinge cams - one pair on each door. On my sister's fridge, the bottom cam of the pair appeared to be riveted onto the frame - rendering it impossible to replace. You may be able to replace both interlocking cams or only the top half cam. You won't know until you lift the door off and look. The bottom cam sits at a 90 degree angle to the door cam and it remains attached to the bottom frame of the refrigerator. These are easy to replace and their design is ingenious. The job is simple and well worth tackling if only to see how your door works. My sister's bottom cam was worn out, but not broken. The blessing: replacing the top half of that cam - the part attached to the bottom of the door - allowed the door to open and close LIKE NEW! The door worked perfectly and I'm thankful to Parts Select for having the hard-to-find cam and for shipping it overnight to me while visiting my sister in Ohio. Now her 20 year old refrigerator door closes on its own, tight as a drum, as if it was brand new. To be safe, I ordered (2) pieces - the matching top and bottom of the pair - but due to the rivet, could only replace one cam. The original $3 "fiber" shim was still good, but I replaced it anyway. I recommend taking cell phone photographs as you go so you know exactly how to re-assemble the three or four interlocking parts of the hinge. I referred to my photos as I re-assembled the new cam. Clearing items off the fridge door: 10 minutes. Removing the shelves, unscrewing the top and lifting the door to the counter: 10 Minutes. Disassembling the hinge, cleaning the area and reassembling the cam/hinge: 20 Minutes. Cleaning the bottom cam area of the Fridge mount and re-mounting the door: 10 Minutes.

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.

Best for 2 people on this repair as 1 person needs to hold the door and the other position the bottom pin in place on reassembly. On my side by side I was replacing the cam on the cold food side, not the freezer. But I got down and inspected both the broken cam and the cam on the side that wasn't broken to understand how the parts fit together. Each door has 2 cams that work/fit together. So be sure the one you are replacing is installed properly (flat side towards the door body). Remove all contents from inside door including the shelves. Use a phillips screwdriver to remove the cover plate on the top hinge. Use tape or a marker to mark on the refrigerator top a corner of where the bracket is positioned, for proper placement on reassembly. While someone is holding the door, remove the 2 bolts from the top bracket (or the back one is just loosened so bracket can be moved out of the way). Lift door off the bottom pin. Turn the door on its side to expose the bottom bracket. There should be 2 bolts here. The furthest one from the pin only needs to be loosened. The other bolt will need to be removed but as you do this be sure to not let the other 2 metal pieces fall out. Remove the broken cam and replace with the new part. Realign the parts and bracket over the pin rod hole and tighten both bolts. Replace the door onto the bottom pin. Then add top bracket and align it to the marking and screw back in these 2 bolts. Test door for any needed adjustments (I had none). Then replace the top bracket cover with its screw. Voila! Clean the shelves and put them in the door and fill them up. :-)