CSK27PFXDAA Hotpoint Refrigerator - Instructions

Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)

I had to defrost large chunks of ice from the rear of the freezer compartment and tried reactivating the ice maker several times before deciding to order the replacement fill tube grommet and clamp. This was very stressful and complicated to accomplish while trying to avoid food spoilage, and consumed a lot of time. It involved removing the ice maker and various panels, plus disconnection of 2 electrical plugs, then using a hair dryer to melt ice build up. The installation of the new parts was quick and simple once they arrived in the mail, and this appears to have solved the leak problem. The fill tube slides easily into the grommet and the clamp, tightened with a screw driver, secures the water feed line on the other end. Fill tube must be carefully threaded through rear panels and into the ice maker receptacle and the grommet needs to be pushed hard and wiggled in order to seat properly in the rear surface of the refrigerator.

Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

I removed the old slide rail, and replaced it with the new one...in about 5 minutes! My drawers don't fall anymore! SUPER FAST shipping! I commend you...I ordered it one day, and it arrived the next day! Now THAT'S service! Thanks.

removed the inside fridge electrical panel and swapped switches

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

Follow instruction on the video you provided

Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

The part broke on Sat, my husband was out of town..I decided early Sunday morning to research the parts. I found partselect through my google search, just loved the site...very easy to locate the parts I needed...watched the video and decided I could fix it myself. Two days later I received the parts and it took me about 20 minutes to make the repair ..it was such a good feeling to know that I did it myself...I did not even have to rely on my husband ...love ...love...love this website!

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

easy pry out, disconnect wiring, connect on new switch and press in switch.

I had read from your sight, to simply cut the lines at the reservoir and tape the new lines to the old. Then use the old lines to pull/feed the new lines to the coupler/valve. This worked great and greatly decreased the time it took to install. I spent more time moving out the frig and cleaning up all the dust (probably should do that more often)