CSK27DHXAAA Hotpoint Refrigerator - Instructions

I took the ice maker tray out and dumped the ice and then removed 4 screws to take the plastic front off the drawer. I then took 4 more screws out to remove auger assembly. I could now unscrew the broken nut and replace it with the new one and put the snap ring and washer back in place and then put everything back together. Done
Had I had my lathe running at the time I would have made this part out of aluminum instead of the new one and original that is out of plastic which is why it did not last.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

1. Turned off the water supply to the refrigerator.
2. Removed the front panel and disconnected the water line to the front left.
3. Removed the left rear (freezer side) panel and disconnected the reservoir from the main water supply input. This was a little tricky to figure out. You must push in the water line at the same time pushing in the coupling. Then pull the line out while keeping the coupling pressed in.
4. Removed the screw that holds the reservoir to the back of the refrigerator.
5. Pulled the old reservoir out and replaced it with the new one.
6. Basically the rest is the reverse of the above. It took a little bit to fish the lines through the original path they came.

Overall this was an easy repair. If I had known how the coupling in step 3 worked this would have been a 15-minute project.

Removed the Ice Maker container. Removed the one screw that held the remnant of the old light shield. Placed the new light shield in place and installed the screw. 5 Minutes from start to finish.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Found your web site and bought a couple of replacement parts from you guys and reaaembled unit. Its now working. Only issue I had was in the reassembly of the auger unit, wasn't quite sure of the blades etc. and the proper order Saw the sketch on your site and figured it out from that. Will visit you guys again when I need a part. Good delivery and timely. Thanks and regards Gil

Removed the broken rail by removing two screws. Put one screw through the hole in the new rail, matched it to the hole in the side of the fridge, and tightened it - not too tight! Then guided the second screw into place and did the same thing. Replaced the drawer. Job done.

Identifying the part on the website was a breeze too, thanks to well-organized site, a picture of the part to match to my broken one, and even a video of a repairman making the repair. Couldn't have been easier, and probably saved me about $100.

I was astonished when my part (PS306943 SLIDE ASM LH (Drawer Slide Rail - left side)arrived the very next day!!
In a big box, beautifully wrapped.
I got out my screw driver, detached the dead shelf support and screwed in the new one.
Oh it's so very nice to have the fridge working again, and so soon.
Hooray for Part select.com
The best thing since sliced bread.
Jill

Removed 2 screws on each slide, Screwed in new slide. Done! The hard part was picking the correct part #. Ordered the wrong parts. Parts Select representative helped me get the correct part # and assisted with the return. Thanks.

Emptied the ice from tray.
Removed the four screws that hold the face plate.
Removed the four screws that fasten drive housing to the tray.
Slid the drive cup into place at the end of the auger.
Made sure the rubber gasket was in place .
Replaced the four screw that hold the housing to the tray.
Replaced the four screws that hold the face plate.
Put some ice cubes in the tray and tested to be sure everything worked properly.

we took off the old one and replaced it.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

SNAPPED THE NEW SHIELD IN PLACE. DONE!

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

The gasket I received was stated to supposedly fit my refrigerator, and the box even had printed on it that the gasket was magnetic. However, after going through the difficult process of removing the old one and installing the gasket that was sent me, I discovered that the new gasket WAS NOT MAGNETIC, and would not keep the freezer door closed. I repaired the cracked area on the old gasket and reinstalled it on my refrigerator. When I called Part Select to return the defective part, I was given every excuse in the book, including that the gaskets aren't made with magnets any more, even though the box stated it WAS SUPPOSED TO BE MAGNETIC......just like I was supposed to GET RETURN INFORMATION BY EMAIL that I have never gotten, and my emails are ignored as far as returning it. I WILL NEVER PURCHASE FROM THIS COMPANY AGAIN....