CSK22GABBAD Hotpoint Refrigerator - Instructions

Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.

First take all your junk off the shelf (with the broken rail of course), take the glass shelf off. Remove screws (phillips). Throw away old rail. Replace new rail, tighten screws. Replace shelf, replace junk. You're done.

I removed the two screws from the old broken rail using a regular star screw driver and replaced the new rail you sent us. Took only 2 mints to do all.

This was so easy! I got the part number off of the broken part, ordered online, and it was delivered the next day!!! So fast! Then I just unscrewed the broken part and reused the existing screws to install the new one. It took about 5 min.

Thanks for making everything so fast and easy!

First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.

The drawer slide broke and I just removed the 2 screws that were still in the side of the refrigerator. I then screwed the new drawer slide in the same holes and it was done!! Simple, simple....even for me, the housewife.... ; )

1) The large drawer is first removed from the guide that remained on the side wall.

2) Removal of the light shield from the rear of the glass shelf to facilitate glass shelf removal by lifting the rear edge of the glass and remove it.

3) Unscrew two phillips head screws holding the remaining pieces of the plastic guide to the interior side panel of the fridge.

4) Examine the replacement guide and insure that the nylon guide and stop parts are clicked into place. If unsure, look at the guide on the other side to ensure that both are present and completely seated before installation of the replacement guide. (These usually fall out of the guide during shipping and should be in the bag with the guide!)

5) Once the guide is outfitted with the nylon guides, secure the new guide with the two phillips screws and DO NOT over tighten, remember you are dealing with plastic guide and steel screws going into a steel cabinet.

6) Re-install the glass shelf, followed by the light shield and finally the large drawer which should slide out smoothly to the stop and back closed without any drag.

7) A successful installation usually includes giving the drawer and glass shelf a good cleaning that probably could be done to the entire fridge side of the unit.

I would recommend removing the dor first as I had to do this after fighting with the drawer to get it out.
There is a cap on the hinge that has one screw, then two nuts and the door is off. From there the drawer rails are easily replaced.

I removed the old broken part and replaced with the new part. Simple as pie, my husband was so happy and impressed I had it done by the time he got home from work!!!!

I removed the drawer and broken piece, then I screwed in the two screws to put the new piece in place. I then had trouble putting the shelf back in place due to the piece being a little bent. I loosened the front screw and was able to manuver the shelf in place with a little force. The new bracket works great.

First I removed the two screws that held the slide in place. I then pulled the slide out and lined up new slide and reinstalled the screws.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair

I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You'll have to drill out a rivet on bottom hinge but it will save over $30.00.