CSH24GRTAAA Hotpoint Refrigerator - Instructions

Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)

1. Turn water supply off at wall. Unpulg referigerator. Remove all cardboard backing covering valve. Vaccum under ref. Unscrew water line where it attaches to valve on ref. (Reuse this later) unplug 4 electrical prongs. Mark with colored pen if not already color coded, so can put back correctly. Pull old ice maker and ref water supply out of valve if it does not screw in with nut. Cut very short peice off end of ref water lines. Slide new locks on water supply lines and push into water valve very hard to lock. Cant get them wrong as they are different sizes. Plug in electrical connectors same as you unpluged them. Connect water line to valve from wall. Turn water on and check for leaks. If none. Replace all screws on backing. Recheck for water on floor. If none congrads, just saved yourself about $120. 00 Labor. Take 2 asprin, drink a six pack and go to bed.

Best for 2 people on this repair as 1 person needs to hold the door and the other position the bottom pin in place on reassembly. On my side by side I was replacing the cam on the cold food side, not the freezer. But I got down and inspected both the broken cam and the cam on the side that wasn't broken to understand how the parts fit together. Each door has 2 cams that work/fit together. So be sure the one you are replacing is installed properly (flat side towards the door body). Remove all contents from inside door including the shelves. Use a phillips screwdriver to remove the cover plate on the top hinge. Use tape or a marker to mark on the refrigerator top a corner of where the bracket is positioned, for proper placement on reassembly. While someone is holding the door, remove the 2 bolts from the top bracket (or the back one is just loosened so bracket can be moved out of the way). Lift door off the bottom pin. Turn the door on its side to expose the bottom bracket. There should be 2 bolts here. The furthest one from the pin only needs to be loosened. The other bolt will need to be removed but as you do this be sure to not let the other 2 metal pieces fall out. Remove the broken cam and replace with the new part. Realign the parts and bracket over the pin rod hole and tighten both bolts. Replace the door onto the bottom pin. Then add top bracket and align it to the marking and screw back in these 2 bolts. Test door for any needed adjustments (I had none). Then replace the top bracket cover with its screw. Voila! Clean the shelves and put them in the door and fill them up. :-)

I had to defrost large chunks of ice from the rear of the freezer compartment and tried reactivating the ice maker several times before deciding to order the replacement fill tube grommet and clamp. This was very stressful and complicated to accomplish while trying to avoid food spoilage, and consumed a lot of time. It involved removing the ice maker and various panels, plus disconnection of 2 electrical plugs, then using a hair dryer to melt ice build up. The installation of the new parts was quick and simple once they arrived in the mail, and this appears to have solved the leak problem. The fill tube slides easily into the grommet and the clamp, tightened with a screw driver, secures the water feed line on the other end. Fill tube must be carefully threaded through rear panels and into the ice maker receptacle and the grommet needs to be pushed hard and wiggled in order to seat properly in the rear surface of the refrigerator.

Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !

replaced with new ones

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.

This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.

Replaced valve with only one difficulty - the electrical spade connectors were different size. Did not come with adapters, as described on the web site.

removed the inside fridge electrical panel and swapped switches

took the old gasket off. cleaned the area were the old gasket was,also cleaned the metal screwdown brakets. put the new gasket in hot water to make it easier to work with. then put the metal in place on the new gasket. place the new gasket in place on the door. then put 1 screw in the middle of the long sides, then did the all 4 corners. then only snug the rest of the screws at first. take your putty knife and slide it under thegasket to seat it squarely on the door. tighten and done.

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

Follow instruction on the video you provided