CSF24EMP Hotpoint Refrigerator - Instructions

replace the lower door hinge assy. and closer cam as a set.Only used a 1/4" socket and ratchet.The process was very easy without any problems.

Followed easy video instructions. Loosened the necessary bolts, etc. Replaced hinge assembly, lined up door, lubed the hinge with vasoline. Works perfectly now. May purchase another assembly as spare as it appears this may be a common repair issue.

I watched the "How To" video on the Parts Select web site twice. The video was very helpful, kind of like having someone right there with you showing you how to replace the hinge. I emptyed the door shelves, removed the top hinge hexscrews and easily lifted the door off the lower hinge, pieces of the broken cam hinge on the door fell off. I set the door on the floor in front of the sink with the handle edge on the floor. I unbolted the hinge and installed the new one. I loosened one screw on the door cam hinge and removed the other, easily replacing the broken part. Before tightening the screws I checked to make sure the hinge hole in the door was not blocked by the new cam hinge. I lifted the door and water ran out from somewhere. I tried to set the door on the lower hinge several times with no luck. I rechecked the hole, it was still clear. I tried placing the door on the refrigerator using the seal to hold it in place, that worked but I couldn't get the door to drop down onto the hinge. I played with it some more and finally got it in place, reinstalled the top hinge, mopped up the water and tried the door. It didn't self close. I adjusted the top hinge a couple of times and applied a little silicone to the hinges, it still didn't self close. I told my wife to make sure the door closes completely and reloaded the stuff into door. After a couple of days it now closes by itself like it's supposed to. In retrospect, I was alone doing the replacement and it really was an easy job but a second person to help line up the lower hinge would have helped a lot.

I watched the repair video. Replaced the cam on the bottom of the door and the hinge pin. Now the door closes on its own, just like brand new.

Removed top hinge, lifted door from bottom post. Removed post with nut driver/socket, removed corresponding bracket/receiver from door. Attached new parts to refrigerator base and bottom edge of door. Was careful to replace part pieces in the same order as original, and secured tightly. Lifted door onto bottom hinge post, leveled the door and replaced top hinge.

I blocked the bottom of the door(CAREFULLY!!) in position to elevate the door & take strain off the lower hinge & pivot post, while maintaining proper door alignment. I removed the two screws holding the hinge & post assembly from the frame, saving the screws & spacer for reuse. I removed the two screws holding the upper cam bracket on the door, again keeping the attaching parts. I installed and carefully aligned the new cam, original spacer & retaining plate to the lower edge of the door. I installed the new hinge & post assembly using the existing spacer & screws. I aligned the door & seal while checking the gap from top to bottom and from side to side. I carefully tighten the screws and rechecked the gap between the door & frame as well as the alignemnt of the door seal. Once satisfied with the alignment, I finished tightening the screws. I emphasize care and extreme caution in reinstalling the screws, they are a self-tapping (self-threading) type of fastener and this requires caution to make sure they are started and installed in the original threads of the door & frame. I put them all in using only finger pressure until I was positive they were started straight, going into the original threads, NOT trying to cross-thread or cut new threads, the structure is too thin for that and stripped threads will result! The door alignment and gap spacing is critical, make sure to check these adjustments carefully to ensure proper operation. Total time of repair, less than 15 minutes. I hope I have not over-simplified this because I have over 55 years of Automotive shop experienced and an ASE Certified Master Auto & Truck Technician...:-)

I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

take fan out,put new in

Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

With my wife's help, we emptied the door shelves and removed the door to the kitchen table. The video and instructions for replacing the parts were 100% right. We probably spent more time cleaning the door bottom and gasket than actually changing the hinge assembly! The job went very smoothly and saved us from overspending on a repair to this old fridge, or worse, making a quick decision on buying a new one.

I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!

I just followed the video instruction supplied by PartSelect and the whole thing was a breeze.

Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.

Followed the u tube video that was on the Part select website. Very easy install when following the video.