Models > CSF22TBM > Instructions

CSF22TBM Hotpoint Refrigerator - Instructions

All installation instructions for CSF22TBM parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSF22TBM
16-30 of 310
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

refigerator door doesn't close completely by itself

  • Customer: Robert from Turnersville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 11 of 12 people found this instruction helpful
Replaced broken riser cam set. Removed door by taking off top hinge pivot. (cap - 1 screw and hinge pivot - 2 screws). Lift door off bottom hinge pivot. Replace upper cam attached to bottom of door. Replace lower cam and hinge pivot assembly. (2 screws). Place door back onto lower hinge pivot and re install top hinge pivot to secure door. Adjust lower hinge pivot to achieve proper door height.

Ice was melting and freezing in bucket

  • Customer: John from Lodi CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 11 of 13 people found this instruction helpful
Frig and freezer were defrosting and refreezing other than normal. Home warranty contractor told me ice maker was faulty. Purchased new ice maker. Unplugged frig, loosened 2 screws with nut driver. unplugged old ice maker, lifted old ice maker out. Took old fill cup off old unit and put on new unit since new fill cup was a different size. Swapped ice maker insert from old to new unit. Plugged in new ice maker, slid over the 2 screws, tightened, and plugged in frig power. New ice maker works fine but still have defrosting and refreezing problem. Figure old ice maker probably works just fine. New contractor still trying to solve problem. Have had problems with this GE Monagram keeping proper temps since it was new in 2005, don't recommend it.

CAMS ON FREEZER DOOR BROKE

  • Customer: WALTER from FROSTBURG MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 10 of 11 people found this instruction helpful
REMOVED TOP HINGE AND ELECTRICAL CONNECTOR (FREEZER DOOR HAS ICE AND WATER DISPENSERS) THEN HAD TO TURN OFF WATER SUPPLY TO UNIT AND DISCONNECT THE HOSE TO THE DOOR AND REMOVE THE SPRING PROTECTOR FROM THE HOSE -- THIS REQUIRED REMOVAL OF THE COMPRESSION FITTINGS IN THE WATER LINE SO SPRING WOULD COME OFF OF THE TUBE.
THEN REMOVED BOTTOM HINGE FROM THE DOOR AND USED SAW TO REMOVE THE RIVET THAT HAD HELD THE CAM TO THE HINGE, USED A NUT AND BOLT TO ATTACH NEW CAM. PUT OTHER CAM (USED TWO) IN THE HINGE AND REPLACED LOWER HINGE UNIT ON THE DOOR. THEN REATTACHED BOTH HINGES TO THE REFRIGERATOR AND LINED UP THE DOOR PUT THE SPRING PROTECTOR AND COMPRESSION FITTINGS BACK ON PLASTIC TUBING AND RECONNECTED THE WATER SUPPLY AND ELECTRIC FITTING, TURNED ON WATER TO UNIT AND PRAYED THERE WERE NO LEAKS. PRAYER WAS ANSWERED, THE WATER DISPENSER WORKED PROPERLY AND THE ICE MAKER FILLED WITH WATER SO I THEN REPLACED THE HINGE COVER ON TOP OF THE UNIT AND THE GRILL AT THE BOTTOM AND HAD A PEPSI. A FEW YEARS AGO I HAD REPLACED THE CAMS ON THE OTHER DOOR WHICH HAD NO WATER/ELECTIC CONNECTIONS AND WAS A MUCH SIMPLER JOB.

Refigerator door would no longer self close

  • Customer: Melvin from Philomath OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 11 people found this instruction helpful
Moved all items from door storage into refrigerator shelves. Removed top hinge cover held by single screw and top hinge plate held by two bolts. Lifted up door to clear bottom hinge pin and removed door. Covered open front of refrigerator with plastic wrap to keep cold in refrigerator with door removed. Laid door on kitchen counter top and removed bottom hinge assembly held on by two bolts. Replaced upper cam located on bottom of door and screwed the hinge assembly back on to bottom of door (helps to keep the three plates in same sequence and note the position of cam). Drilled out the rivet that holds the lower cam to the bottom hinge pin. Removed old lower cam and and replaced with new cam and secured to lower hinge assembly with pan head screw and nut (instead of rivet). Replaced door back onto lower hinge pin and secured upper hinge pin with original bolts. Placed cover on upper hinge assembly and secured with original screw. Removed plastic wrap from front of refrigerator and moved the items that originally were stored in the door back to provide weight needed for door to close properly. All done and the door works like new, and all in less than 45 minutes. Would have been a more difficult job without the pioneering of people on this site. Thanks to all!

Motor rattled loudly

  • Customer: Robert from Kingwood TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
Turned off the refridgerator. Took everything out of the freezer compartment & put into ice chest with pleanty of ice on top. Removed 2 screws holding the ice maker in place & placed ice maker aside. Removed shelf. Removed one screw on back plate, pushed up on the holding tabs at the top of the back plate & removed the back plate. Removed 3 screws holding the motor bracket in place along with the 3 wires. Installed new motor & used the wire extensions provided due to the electrical connections on the new motor being on the opposite side. Had to bend one wire tab down to clear the motor bracket. Turned refridgerator back on to ensure correct rotation on the fan. Reinstalled back plate & ice maker & shelf. Waited 30 minutes before putting food items back in freezer compartment.

thermostat control not working properly

  • Customer: Betty from Lake Village IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 22 people found this instruction helpful
repairman came looked it over said problem was thermostat control which was not made anymore and left charging service call $190.00 I went online found the control for $160.00 received it in 3 days put it in 30 mins later working fine.

ice maker not making ice

  • Customer: Cristina from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
just unscrewed the 3 screws, attached the rounded plug that came with the unit and screwed back only 2 screws. ice magic in about a couple of hours

Refrigerator door wouldn't close right

  • Customer: Anthony from Highland Lakes NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 10 of 14 people found this instruction helpful
GET 2 "door closing cams"
Yep. same as some others here. found some black plastic pieces on the floor, when door wasn't closing right. I took the door off by taking off the top bracket. very easy. bottom bracket has the broken cam riveted to it. need hacksaw to get this off then punch it through with hammer and a screwdriver. this is the only part that took a little while. replace the closing cam and find a small nut & bolt or screw to replace the rivet you just sawed in half.
Replace the closing cam that is on the bottom the the door as well. even if yours isn't broken. replace it anyway. put door back on and done. not a diffucult project if you know about the rivet and needing 2 closing cams beforehand. good luck

Noisy Fan Motor - Bearing went out.

  • Customer: Robert from Carpinteria CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 9 of 12 people found this instruction helpful
Moving the frig out and cleaning was the hardest part of this job - lots of dust collected over the 17 years the frig was in place. Once all the cleaning was done, with the frig out and back cover off (10 -12 screws taken off with nutdriver),I plugged the frig in and observed the the problem was a noisy fan motor. The motor is at the very back of the frig with easy access to the 3 brackets holding it in place.
Pull off the electrical clip. Remove the screw holding the bracket to the frame on the front bracket, leaving the bracket attacked to the fan. The other two screws remove from the fan, leaving the brackets in place.
Reverse the procedure when you receive the new part from PartSelect(great company to deal with)!

Failed Icemaker

  • Customer: GARY from PARRISH FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 15 of 30 people found this instruction helpful
Shut off power to the refrige. Removed old icemaker, using large hammer. Installed new unit.

Ice machine wasnt making ice

  • Customer: Robert from Auburn AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 16 people found this instruction helpful
First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection back in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!

Freezer compartment stopped cooling as it should.

  • Customer: Arthur from Elkhart IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 24 of 58 people found this instruction helpful
Initially I talked to local refrig repair man who told me to defrost the refrigerator and freezer for 6 hrs as well as to use a hot air dryer on the back wall of the freezer to defrost the freezer coils. I defrosted the refrigerator and freezer for twelve hours by unpluging it from the wall and using a fan to blow warm air into the frig/freezer. After 12 hrs., about 1 gallon of water collected in the pan below the refrigerator and I thought it was long enough.(I had defrosted the refrig well. The collection of water in the pan told me that the drainage tubes from the freezer and refrig compartments was working well and not obstructed. This made me think tthat one of three parts on the "no Frost" cycle may be defective and so ordered the Control, Thermostat and Heat assembly from PartSelect for our refrig/Freezer.
They have the most reasonable prices.
I then plugged in the refrigerator and monitored the temp. in the freezer compartment every twelve hours for the next three weeks and noted the temperature in the freezer compartment varied from o degrees to 10 degrees which is what it should do. I also watched for any frost build up in the freezer compartment and to date have not seen any.
The temp in the refrigerator compartment is as it should be. My impression is that all components are actually working as they should now and that the cause for our problem with the Hotpoint was due to the fact that the door was left open overnight. We will try to avoid doing that again.
I am holding the parts for one more week. If the refrig coninues to function normally till then, I plan to return the parts to partselect.com because they said I could do so.

refrigerator did not cool

  • Customer: Carl from Kent City MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 11 people found this instruction helpful
i put a new evaporator motor in and now it works fine

icemaker developed a leak and froze over

  • Customer: debbie from chino hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 11 of 20 people found this instruction helpful
My husband did the repair, and even though our refrigerator is roughly 20+ years old, he was able to adapt it to work in all the right spots and we now have ice cubes! I'm very happy we did not have to spend $2000 on a comparable refrigerator.

broken ice maker

  • Customer: robert from bensalem PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.
All Instructions for the CSF22TBM
16-30 of 310