Models > CSF22TBD > Instructions

CSF22TBD Hotpoint Refrigerator - Instructions

All installation instructions for CSF22TBD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSF22TBD
46-60 of 290
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

FAN STOPS - BAD BEARING

  • Customer: JACK R from LEESBURG FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
UNPLUG UNIT FROM WALL. REMOVED COVER FROM REAR OF UNIT. CLEANED COILS WITH VACCUUM CLEANER. UNPLUG WIRES FROM FAN MOTOR AND REMOVE NUT HOLDING FAN BLADE TO MOTOR. REMOVE 3 SCREWS HOLDING MOTOR TO MOUNT. REPLACE WITH NEW MOTOR,MAKE SURE FAN BLADE DOES NOT HIT HOUSING. PLUG UNIT BACK IN WALL AND REPLACE COVER.

Not cooling - cond fan did not turn

  • Customer: Daniel from Great Falls VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
Unplug refrig! Removed back cardboard covering (~5 screws)
(1) Cleaned all the dust out (hardest part!)
(2) Removed power wire to motor
(3) Removed 3 bolts holding motor to frame
(4) Removed motor/fan blade to the left
(5) Moveded fan blade to new motor (clean it!)
(6) Replaced motor, reinstalled 3 bolts
(7) Plugged power wire to new motor
(8) Tested it - worked fine, failed safe, drained to bilge!
Replaced back cover (had to tape it since I horked it up removing it)

Started to see a little sweat in freezer and ice cream not getting hard frig staying on longer.

  • Customer: Frank from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 3 of 4 people found this instruction helpful
Pulled frig out. Removed back cover. Unplugged frig, unplugged motor. Removed fan from old motor first then 3 screws from bracket that holds motor and removed motor. Reattached motor back on bracket, reattached fan on motor. Plugged fan back in and then frig. Everything worked fine no more soupy ice cream !!

stopped making ice

  • Customer: Timothy from Orange Park FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove from hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

excessive door swing

  • Customer: PETER from ENGLEWOOD NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
Removed the top hinge and the door.
Removed door stop held in place by 2 screws, installed new door stop.
re-installed door and top hinge.
Easy once the correct diagnosis was made
It would have been nice if I could have e-mailed you the symptoms and received an accurate diagnosis. As it developed, I initially replaced the door cam before realizing that the door stop itself had broken.

Existing light switch was hard to remove.

  • Customer: Stephen from Jupiter FL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

unusually noisy

  • Customer: Anthony from South Plainfield NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 3 of 4 people found this instruction helpful
Removed the three screws from old motor body-bracket assembly , pulled off 1/4'' spade terminals and removed shield from terminal block for re-use.
Removed fan from old unit and installed on new,
screwed new motor in place, replaced terminal wires, plugged back in refrigerator.
Now my old rerfrigerator is whisper quiet

DOOR NOT CLOSING TIGHTLY + STAYING OPEN

  • Customer: Jeff from Venice FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
TURNED OFF WATER TO REF , REMOVED BOTTOM KICK PLATE , GOT A TOWEL AND DISCONNECTED THE WATER LINE PLASTIC FITTING AND UN SCREWED THE (2) TUBE CLAMPS UN SCREWED THE COUPLING AND ((CAREFULLY )) SLID OUT THE TUBE FROM THE COMPRESSION FERRELS ! ( BE CAREFUL AND DO NOT BREAK OR DISTORT THEM + REMEMBER EXACTLY THE ORDER THEY ARE REMOVED !
SLID THE PROTECTOR SPRING SHROUD FROM THE PLASTIC TUBE , TOOK OGG THE TOP HINGE COVER THEN REMOVER THE TOP HINGE . CAREFULLY LIFTED THE DOOR OFF FEERING THE PLASTIC TUBE THROUGH THE BOTTOM HINGE WITH MY FOOT ! GOT THE DOOR OFF REMOVED THE BOTTOM HINGE + PUT THE NEW ON ON, THEN REMOVED THE DOOR CAM WHICH WAS BROKEN ON THE BOTTOM OF THE DOOR , LIFTED THE DOOR UP AND CAREFULLY FED THE WATER LINE THROUGH THE NEW BOTTOM HINGE . ATTACHED THE TOP HINGE AND REASSEMBLED THE REST SAME AS I HAD DISSAMBLED IT . TURNED ON WATER ( CHECKED FOR LEAKS ) ! ALL WORKING 100% A-OK ! THIS COMPANY IS THE BEST ! ORDERED THE PART AT 1 PM AND HAD THE PART AT 2 PM THE FOLLOWING DAY MANY THANKS : )

This was a side by side refrigerator that will not close on its own.

  • Customer: Bayani from Saint Louis MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 2 of 2 people found this instruction helpful
Door hinge and cam kit was ordered. Removing the refrigerator door was easy. Then I discovered that the holes on the replacement part did not match the opening. After the opening was drilled screwing in the hinge and cam was easy. Adjustment of the door is necessary after installation of the replacement parts. Piece of cake.

Slide rail broke on one end

  • Customer: Silvia from Hopkinsville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Pulled out the shelves, unscrewed the old rail and removed it. Two screws put the new rail on, and then I put the shelves back in. It was so simple, and inexpensive too. This is a great service you provide. Thanks!!

My veggy drawer wouldn't close or open due to broken rails on left side.

  • Customer: Christine from Central Point OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I looked up the brand (Kenmore) and found that there are replacement parts for the drawer rails. I put up with this problem for three years not knowing this could be repaired. I unscrewed the broken left rail and replaced with the new one. I bought a right side rail just in case all the stress of the other side being broken would cause the right side to give up too. So far so good but I will keep the new right rail for a future date. It was so easy to repair and I wasted all those years putting up with the hassel.

Broken slide rail for Veggie drawer

  • Customer: Tony from Chesterfield MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Emptied the drawer and removed it. Then took off the old slide rail. Then I got some hot soapy water and cleaned the walls of the refridge while I was down there and had everything out. I then installed the slide rail put the drawers back in loaded the fridge and sat back and said I just saved myself about $200.00. You guys are awesome we got the part 2 days after we ordered it Thank you for the great service.

Tony The Birdman

Drawer slide broke

  • Customer: Richard from Tucson AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed 2 screws that hold it on, put the new one in with the 2 screws that were removed.

Door mis-aligned and not closing properly

  • Customer: Ray from Encinitas CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Supported the door to allow removal of lower hinge. Removed lower hinge and cam assembly....and upper cam. Separated worn out lower cam from hinge, then removed rivet which holds cam. Installed new lower cam with small nut and bolt. Replaced upper cam with existing hardware. Re-assembled lower hinge onto refrigerator.

No problem....works like new. You really need to order TWO cams.....there is an upper and lower cam that work together....both are the same part number.

I do question how to do this repair on the freezer side. The water supply line for the ice maker passes through the cam. Any insight ?

The fresh food door on the refrigerator would not stay closed

  • Customer: John from Newport Beach CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!
All Instructions for the CSF22TBD
46-60 of 290