Models > CSF22MBB > Instructions

CSF22MBB Hotpoint Refrigerator - Instructions

All installation instructions for CSF22MBB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSF22MBB
61-75 of 339
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The fresh food door on the refrigerator would not stay closed

  • Customer: John from Newport Beach CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

DOOR NOT CLOSING TIGHTLY + STAYING OPEN

  • Customer: Jeff from Venice FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 8 people found this instruction helpful
TURNED OFF WATER TO REF , REMOVED BOTTOM KICK PLATE , GOT A TOWEL AND DISCONNECTED THE WATER LINE PLASTIC FITTING AND UN SCREWED THE (2) TUBE CLAMPS UN SCREWED THE COUPLING AND ((CAREFULLY )) SLID OUT THE TUBE FROM THE COMPRESSION FERRELS ! ( BE CAREFUL AND DO NOT BREAK OR DISTORT THEM + REMEMBER EXACTLY THE ORDER THEY ARE REMOVED !
SLID THE PROTECTOR SPRING SHROUD FROM THE PLASTIC TUBE , TOOK OGG THE TOP HINGE COVER THEN REMOVER THE TOP HINGE . CAREFULLY LIFTED THE DOOR OFF FEERING THE PLASTIC TUBE THROUGH THE BOTTOM HINGE WITH MY FOOT ! GOT THE DOOR OFF REMOVED THE BOTTOM HINGE + PUT THE NEW ON ON, THEN REMOVED THE DOOR CAM WHICH WAS BROKEN ON THE BOTTOM OF THE DOOR , LIFTED THE DOOR UP AND CAREFULLY FED THE WATER LINE THROUGH THE NEW BOTTOM HINGE . ATTACHED THE TOP HINGE AND REASSEMBLED THE REST SAME AS I HAD DISSAMBLED IT . TURNED ON WATER ( CHECKED FOR LEAKS ) ! ALL WORKING 100% A-OK ! THIS COMPANY IS THE BEST ! ORDERED THE PART AT 1 PM AND HAD THE PART AT 2 PM THE FOLLOWING DAY MANY THANKS : )

switchlight on my refrigerator was not working

  • Customer: Eileen from Coto de Caza CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 4 of 8 people found this instruction helpful
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

Slide rail was missing when we bought house

  • Customer: Joe from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service

Needed left and right drawer rails for crisper

  • Customer: Joanne from West Columbia SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I was so pleased to find your website. We have just one company here in Columbia,S.C. that sells refrigerator parts. I did find out that they wanted about $60.00 for both pieces. Needless to say,I was just going to do without. I knew there had to be someone else. I found you guys on line,ordered my parts for a little over $5.00 a piece,and I put them in myself. I'm talking standard GE parts,not knockoffs. I am so pleased. Thanks for being there. I tell everyone about you.

worn/broken cam , door doesn 't self close

  • Customer: Charles from Franklinville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

Door wouldn't close properly

  • Customer: John from San Marino CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.

Refrigerator door won't close

  • Customer: CYNTHIA from NEWARK DE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 3 of 6 people found this instruction helpful
First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

Right fridge door had to be propped shut with a chair

  • Customer: Peter from Douglassville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
Took off top hinge, door came off, pried cam off of rivet on bottom hinge assy. used 2 pair of pliers to force new cam over rivet, add shims and another cam up on door.Put door back on -all done!

fridge door would not stay closed,

  • Customer: glen from broadway NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
took off the top hinge (one screw on the cover, and two bolts holding the hinge), lifted the door off the bottom hinge, saw that the riser cam had disintegrated. ordered the cam and the shim (since it looked like the shim was also going bad).
when the parts arrived, I took the top hinge off again, took the bracket holding the shim and cam off the bottom of the door (two bolts), removed the broken riser cam. Attached the shims and the cam to the bottom of the door with the bracket, replaced the door on the bottom hinge, replaced the top hinge, and the door closed correctly.

after three days, there was no condensation in the fridge, we decided that the gaskets did not need to be replaced.

qed.

Difficulty in removing the old switch

  • Customer: James from Federal Way AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

Noisy refrigerator.

  • Customer: Rodney from Lafayette LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 6 people found this instruction helpful
Remove the 4 screws holding the back cover onto the refrigerator. Unplug the power for the refrigerator. There's 3 bolts holding the fan motor assembly to the refrigerator. Loosen the two bolts which allow the brackets to pivot out , and remove the third bolt. Disconnect the electrical leads, and remove the fan blade, then rotate the fan motor assembly out from the refrigerator. Install mounting brackets from the old motor onto the new motor, then reinstall the assembly in the reverse order of removal.

Refirigerator door would not close all the way on its own.

  • Customer: Kenneth from Virginia Beach VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 1 of 1 people found this instruction helpful
The repair went well could have completed the job in 20 minutes if I had a selection of small nuts and bolts to replace the rivet that had to be drilled out. Also buy 2 of the door closing cams Part # PS297995 one goes on the bottom hinge of the refrigerator door the other on the bottom of the refrigerator.

Refrigerator door was not closing fully and was about 1/2 lowere than it should have been

  • Customer: Richard from haverford PA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
This was a 15 year old great working GE regrigerator. Refrigerator was not cooling properly, though the freezer worked great. Using flashlight, examined cam riser which was clearly broken. YOU MUST ORDER TWO GASKETS AS BOTH WILL BE WORN. After removing all food from the door, taped plastic sheet over the open space to keep food somewhat cool Removed top hinge cover and screws on top of door and lifted door out of bottom bracket placing it flat on kitchen island. Unscrewed hinge elements including old broken cam and shims form the bottom of the door and fit in the new cam. Unfortunately one of the shims was broken, so I used a thin plastic black washer from the hardware store which was big enough to fit over the pin on the bottom of the refrigerator itself. Screwed all the parts back together. Be VERY careful to note how you removed them in the first place...mabe take a digital foto or two. This was kind of tricky to remember. Then used a hammer and chisel to break off the rivit holding the bottom hinge elements on the refrigerator. Sawing with jigsaw didn't work that well. The rivit came right off. Then used a flat head screw, lock washer and nut instead of a reivit and attached the new second cam riser. You are now done with the new parts. Simply reattached the door and it closed like new. Had a simultaneoius problem with a faulty defrost heater in the freezer which also had to be replaced and which was really easy to do. About an hour max. This was the real cause of the refrigerator not cooling properly. But that's another story.

Door wouldn't close tight automatically.

  • Customer: Les from San Francisco CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
1. Put all perishable food into ice chest. Empty door shelves.
2. Remove top hinge cover with Philips screwdriver.
3. Supporting door, remove top hinge attached by two hex screws.
4. Lift door off bottom hinge.
5. On bottom of door, unscrew the hex screw holding the broken plastic cam.
6. Loosen the second hex screw enough to free the broken cam.
7. Replace the cam and tighten the hex screws making sure the opening of the cam lines up with the hole under the door.
8. Snap off plastic grill at the bottom of the refrigerator.
9. Remove bottom of the two hex screws holding the bottom hinge tot eh refrigerator body.
10. Loosen the second screw enought to rotate the hinge upsidedown. Tighten the screw again.
11. Now the rivet bottom is exposed so as to facilitate drilling it out to remove the broken cam.
12. Loosen the hex screw again and turn it back rightside up. Reinstall the bottom screw and tighten both of them.
13. Using an appropriate size bolt, lockwasher and nut, install other new cam.
14. Reinstall door reversing steps 1 to 4.
15. Don't forget to return the food to the 'fridge, by the way!
All Instructions for the CSF22MBB
61-75 of 339