Models > CSF22EBC > Instructions

CSF22EBC Hotpoint Refrigerator - Instructions

All installation instructions for CSF22EBC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSF22EBC
196-206 of 206
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door would not close properly at the last few inches, now it closes good at this time but now need to be raised up to the 5/8 inch as the book says, haven't done that yet

  • Customer: Carol J from Alexandria KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the door closing cam works fine.

bad fan motor

  • Customer: theodore from salisbury NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
take fan out,put new in

The girlfriend opened the door and then it wouldn't shut on its own or stay closed

  • Customer: Gregory from Ontario CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Empty door first then take a phillip heads screw driver and unscrewed the top hinge cover 1 screw. Then used 5/16 nut driver to loosen top hinge from fridge. remove door by lifting and then lay on table to replace the lower washer that is held in by 2 screws and you only need to loosen one all the way leaving one in to align then replace and tighten it up your done.

Drawer Slide Rail cracked/broken

  • Customer: William from Bossier City LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video supplied by manufacturer and followed the instructions. Very easy.

Door would not shut tight

  • Customer: Peter from Tarrytown NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Followed Partselect video on how to replace cam riser. Very, very helpful!

the old slide broke

  • Customer: darlene from phoenix OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
when I got on your site I was able to find the part easily & your installation video was a big help. It fit perfectly & was very easy to install--it's working great!!!!!thank you so much

broken shelf bracket

  • Customer: Darlene from Delaware OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the you tube video. Very easy! the part was easy to order came earlier that expected and was fixed in less than 5 minutes!

broken left siderail

  • Customer: Thomas from Frederiksburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrew 2 screws to remove broken part, screw in new.

Refrigerator Door Won't Self-Close

  • Customer: Jan from Westerville OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First off, Parts Select has a great YouTube video showing exactly how to replace this refrigerator hinge cam. This repair was for my sister's 20-year old GE refrigerator. I used to do this same repair every 3 years on an expensive fridge my wife and I owned - one that had additional wood panels mounted on the door. The panels exceeded the hinges' designed weight limit, so every 3 years I replaced the bottom plastic hinge cams. On that fridge, I could replace BOTH interlocking hinge cams - one pair on each door. On my sister's fridge, the bottom cam of the pair appeared to be riveted onto the frame - rendering it impossible to replace. You may be able to replace both interlocking cams or only the top half cam. You won't know until you lift the door off and look. The bottom cam sits at a 90 degree angle to the door cam and it remains attached to the bottom frame of the refrigerator. These are easy to replace and their design is ingenious. The job is simple and well worth tackling if only to see how your door works. My sister's bottom cam was worn out, but not broken. The blessing: replacing the top half of that cam - the part attached to the bottom of the door - allowed the door to open and close LIKE NEW! The door worked perfectly and I'm thankful to Parts Select for having the hard-to-find cam and for shipping it overnight to me while visiting my sister in Ohio. Now her 20 year old refrigerator door closes on its own, tight as a drum, as if it was brand new. To be safe, I ordered (2) pieces - the matching top and bottom of the pair - but due to the rivet, could only replace one cam. The original $3 "fiber" shim was still good, but I replaced it anyway. I recommend taking cell phone photographs as you go so you know exactly how to re-assemble the three or four interlocking parts of the hinge. I referred to my photos as I re-assembled the new cam. Clearing items off the fridge door: 10 minutes. Removing the shelves, unscrewing the top and lifting the door to the counter: 10 Minutes. Disassembling the hinge, cleaning the area and reassembling the cam/hinge: 20 Minutes. Cleaning the bottom cam area of the Fridge mount and re-mounting the door: 10 Minutes.

slide fell apart

  • Customer: sandra from Danville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered part on line, arrived the next day. Looked at the screw (phillips head). Had trouble dropping screws but got our magnetic phillips head and it worked like a charm. So proud of myself as my husband did not have to do a thing.

The motor was making a thumping out of balance sound.

  • Customer: Alan from Spring Valley IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.
All Instructions for the CSF22EBC
196-206 of 206