Models > CSF20EBD > Instructions

CSF20EBD Hotpoint Refrigerator - Instructions

All installation instructions for CSF20EBD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSF20EBD
46-60 of 259
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

fridge door would not stay closed,

  • Customer: glen from broadway NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
took off the top hinge (one screw on the cover, and two bolts holding the hinge), lifted the door off the bottom hinge, saw that the riser cam had disintegrated. ordered the cam and the shim (since it looked like the shim was also going bad).
when the parts arrived, I took the top hinge off again, took the bracket holding the shim and cam off the bottom of the door (two bolts), removed the broken riser cam. Attached the shims and the cam to the bottom of the door with the bracket, replaced the door on the bottom hinge, replaced the top hinge, and the door closed correctly.

after three days, there was no condensation in the fridge, we decided that the gaskets did not need to be replaced.

qed.

Right fridge door had to be propped shut with a chair

  • Customer: Peter from Douglassville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Took off top hinge, door came off, pried cam off of rivet on bottom hinge assy. used 2 pair of pliers to force new cam over rivet, add shims and another cam up on door.Put door back on -all done!

Started to see a little sweat in freezer and ice cream not getting hard frig staying on longer.

  • Customer: Frank from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 3 of 4 people found this instruction helpful
Pulled frig out. Removed back cover. Unplugged frig, unplugged motor. Removed fan from old motor first then 3 screws from bracket that holds motor and removed motor. Reattached motor back on bracket, reattached fan on motor. Plugged fan back in and then frig. Everything worked fine no more soupy ice cream !!

Needed left and right drawer rails for crisper

  • Customer: Joanne from West Columbia SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
I was so pleased to find your website. We have just one company here in Columbia,S.C. that sells refrigerator parts. I did find out that they wanted about $60.00 for both pieces. Needless to say,I was just going to do without. I knew there had to be someone else. I found you guys on line,ordered my parts for a little over $5.00 a piece,and I put them in myself. I'm talking standard GE parts,not knockoffs. I am so pleased. Thanks for being there. I tell everyone about you.

switchlight on my refrigerator was not working

  • Customer: Eileen from Coto de Caza CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 4 of 8 people found this instruction helpful
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

Slide rail was missing when we bought house

  • Customer: Joe from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service

This was a side by side refrigerator that will not close on its own.

  • Customer: Bayani from Saint Louis MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 2 of 2 people found this instruction helpful
Door hinge and cam kit was ordered. Removing the refrigerator door was easy. Then I discovered that the holes on the replacement part did not match the opening. After the opening was drilled screwing in the hinge and cam was easy. Adjustment of the door is necessary after installation of the replacement parts. Piece of cake.

Slide rail broke on one end

  • Customer: Silvia from Hopkinsville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Pulled out the shelves, unscrewed the old rail and removed it. Two screws put the new rail on, and then I put the shelves back in. It was so simple, and inexpensive too. This is a great service you provide. Thanks!!

My veggy drawer wouldn't close or open due to broken rails on left side.

  • Customer: Christine from Central Point OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I looked up the brand (Kenmore) and found that there are replacement parts for the drawer rails. I put up with this problem for three years not knowing this could be repaired. I unscrewed the broken left rail and replaced with the new one. I bought a right side rail just in case all the stress of the other side being broken would cause the right side to give up too. So far so good but I will keep the new right rail for a future date. It was so easy to repair and I wasted all those years putting up with the hassel.

The drawer rails had broken causing the drawers to drag

  • Customer: Barry from Grenada MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Each rail required removing two screws which were used to install the new rail. Each one took about 5 minutes however cleaning the recesses was the most effort.

slide rails had broken on side by side

  • Customer: Ray from Santa Clarita CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
remove the 8 screws 2 for each rail
installed the new rails
slid in the meat drawer and glass
slid in the vegetable drawer and glass
presto - like new fridge !

DOOR NOT CLOSING TIGHTLY + STAYING OPEN

  • Customer: Jeff from Venice FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 8 people found this instruction helpful
TURNED OFF WATER TO REF , REMOVED BOTTOM KICK PLATE , GOT A TOWEL AND DISCONNECTED THE WATER LINE PLASTIC FITTING AND UN SCREWED THE (2) TUBE CLAMPS UN SCREWED THE COUPLING AND ((CAREFULLY )) SLID OUT THE TUBE FROM THE COMPRESSION FERRELS ! ( BE CAREFUL AND DO NOT BREAK OR DISTORT THEM + REMEMBER EXACTLY THE ORDER THEY ARE REMOVED !
SLID THE PROTECTOR SPRING SHROUD FROM THE PLASTIC TUBE , TOOK OGG THE TOP HINGE COVER THEN REMOVER THE TOP HINGE . CAREFULLY LIFTED THE DOOR OFF FEERING THE PLASTIC TUBE THROUGH THE BOTTOM HINGE WITH MY FOOT ! GOT THE DOOR OFF REMOVED THE BOTTOM HINGE + PUT THE NEW ON ON, THEN REMOVED THE DOOR CAM WHICH WAS BROKEN ON THE BOTTOM OF THE DOOR , LIFTED THE DOOR UP AND CAREFULLY FED THE WATER LINE THROUGH THE NEW BOTTOM HINGE . ATTACHED THE TOP HINGE AND REASSEMBLED THE REST SAME AS I HAD DISSAMBLED IT . TURNED ON WATER ( CHECKED FOR LEAKS ) ! ALL WORKING 100% A-OK ! THIS COMPANY IS THE BEST ! ORDERED THE PART AT 1 PM AND HAD THE PART AT 2 PM THE FOLLOWING DAY MANY THANKS : )

worn/broken cam , door doesn 't self close

  • Customer: Charles from Franklinville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

Broken slide rail for Veggie drawer

  • Customer: Tony from Chesterfield MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Emptied the drawer and removed it. Then took off the old slide rail. Then I got some hot soapy water and cleaned the walls of the refridge while I was down there and had everything out. I then installed the slide rail put the drawers back in loaded the fridge and sat back and said I just saved myself about $200.00. You guys are awesome we got the part 2 days after we ordered it Thank you for the great service.

Tony The Birdman

no problems

  • Customer: Sharon from Kennewick WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First removed the old sliders, then screwed in the new sliders, replaced all four within minutes.
All Instructions for the CSF20EBD
46-60 of 259