Models > CSE9000ADB > Instructions

CSE9000ADB Maytag Cooktop - Instructions

All installation instructions for CSE9000ADB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSE9000ADB
1-15 of 15
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replaced heating element on flat surface stove top

  • Customer: dennis from assonet MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 17 of 24 people found this instruction helpful
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

the left front burner burned out & none of the lights to show if a burner was hot would come on.

  • Customer: Richard from Fair oaks Ranch TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

SMALL ELEMENT ON COUNTER TOP RANGE NOT HEATING.

  • Customer: Brian E from Waldorf MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 7 people found this instruction helpful
1. TURNED OFF POWER TO TROUBLE SHOOT THE COUNTER TOP RANGE ELEMENTS.
2.RAISED THE COUNTER TOP UP TO WORK ON IT AND SLID TWO EVENLY PLACED WOODEN SLATS UNDER THE BOTTOM OF THE HOUSFOR STABILITY SO IT WOULD NOT FALL BACKDOWN INTO THE COUNTER TOP CUT-OUT.
3. WITH A 1/4" NUT DRIVER REMOVED THE 10 HEX-HEAD SCREW THAT WERE HOLDING THE BLACK GLASS TOP IN PLACE, PULLED OFF THE 4 .CONTROL KNOBS AND CAREFULLY REMOVED THE GLASS COVER AND CAREFULLY SEET IT ASIDE IN A SAFE PLACE.
5. A VISUAL INSPECTION OF THE NON WORKING ELEMENT SHOWED THAT IT HAD A BURN OUT SPOT CAUSING IT NOT TO HEAT.
6. GOT THE MODEL NUMBER OF THE APPLIANCE AND CHECKED THE INTERNET FOR PARTS SUPPLIERS, CHOSE PARTS ELECT BECAUSE THEY HAD THE PART IN STOCK AND COULD OVERNIGHT IT FOR REINSTALLATION THE NEXT DAY, PART DID ARRIVE THE NEXT MORNING. A VISUAL INSPECTION SHOW THAT IT WAS THE CORRECT PART AND IT WOULD BE A LIKE FOR LIKE SWAP OUT.
7. PRIOR TO REPLACING THE ELEMENT CHECK TO SEE THAT THE ELECTRICAL POWER WAS STILL OFF AT THE CIRCUIT BREAKER, MADE A QUICK SKETCH OF THE WIRING AND IDENTIFIED THE WIRES SO THAT THEY WOULD BE RETERMINATED AT THE SAME POINTS.
8.USING THE NEEDLE NOSE PLIERS PULLED OFF THE 4 STAKE ON TERMINATIONS.
9. LIFTED OUT THE 6" FROM THE BODY OF THE UNIT , REMOVED THE 4 PHILLIPS SCREWS HOLDING PARTS WHAT WERE TO BE TRANSFERED ONTO THE NEW ELEMENT.
10. TRANSFERED PARTS ONTO THE NEW ELEMENT, REINSTALLED THE ELEMENT INTO THE BODY OF THE UNIT, REINSTALLED THE 4-STAKE-ON WIRES TO THERE APPROPRIATE TERMINALS AND VERIFIED WITH PREVIOUS WIRING SKETCH.
11. REINSTALLED THE GLASS TOP, 10 SCREW HOLDING IT IN PLACE AND THE 4-CONTROL KNOBS.
12 .TURNED MAIN POWER TO THE UNIT BACK ON AND TURNED ON THE REPLACED ELEMENT, IT WORK CORRECTLY, ALSO CHECKED THE OTHER 3 ELEMENTS TO MAKE SURE THAT THEY WERE WORKING CORRECTLY.
13. WHEN THE UNIT HAD COOLED, REMOVED THE WOODEN SLATS AND LOWERED THE COUNTER TOP BACK INTO ITS CUT-OUT MAKING SURE NOT TO DAMAGE THE GLASSTOP.
JOB COMPLETE.

Left front burner went out.

  • Customer: Donald from North Highlands CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 6 people found this instruction helpful
Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 9 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

broken prong that knob fit onto

  • Customer: Lisa from Oklahoma City OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 3 of 5 people found this instruction helpful
This was a piece of cake! We put off doing this for ourselves because we thought it would be difficult. We sold the house and "had" to do it. Turns out we should have done it for ourselves a long time ago.

INDICATROR LIGHT FOR 6" BURNER QUIT WORKING

  • Customer: NANCY from LITTLETON CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
OK this is a glasstop Jenn Air cce3531B, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since i had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. THANKS YOU PARTSELECT

One of the electric stove top elements had burnt out

  • Customer: Anthony from Palmyra VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

element or temperature sensor failed: not working

  • Customer: David from Mary Esther FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

Needed stove top cleaner and scraper

  • Customer: Doris from Camden-Wyo. DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Absolutely perfect, no problems

Lower left Surface Element burnt

  • Customer: John from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.

THE STEM ON THE BURNER CONTROL SW BROKE OFF

  • Customer: charles from franklin LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I USED A PHILLIPS SCREWDRIVER TO REMOVE THE CONTROL SWITCH.I DREW A DIAGRAM ON A PIECE PAPER WHERE THE WIRE CONTACTS CONNECTED I WROTE THE DIFFERENT # AND WIRE COLORS DOWN . I COMPARED THE 2 SWITCHES THEY WERE THE SAME.SO I CONNECTED THE WIRES . I PUT THE 2 SCREWS ON. THE STEM WAS HIGHER THAN THE OTHER SWITCHERS.SO I HAD TO CUT THE STEM SHORTER. IT HAD GROVES SO IT WAS EASY TO USE A HACKSAW TO CUT A LITTLE THEN USE A LOCK PLIERS TO HOLD THE STEM AND ANOTHER TO BREAK IT OFF THEN IT FIT PERFECT I PUT THE KNOB ON PRESTO NEW SWITCH.JUST LIKE NEW.

front burner would not heat

  • Customer: Jack A from Biloxi MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
All Instructions for the CSE9000ADB
1-15 of 15