Models > CSC27HRAAD > Instructions

CSC27HRAAD Hotpoint Refrigerator - Instructions

All installation instructions for CSC27HRAAD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC27HRAAD
481-495 of 509
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bad switch for door prevented interior light from coming on

  • Customer: Patricia from Sylva, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Bulb Replacement

  • Customer: Judith from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

The ice maker did not make any ice cubes

  • Customer: Robert Mc from Citrus Heights, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I pulled the Refrig out of the space so that I could get to the plug and water shut off. After unplugging and turning the water off, I had to remove the 7 screws holding the cardboard cover over the bottom portion of the Refrig. I then had to unloosen the water input to the the valve. Then I removed the screw holding the Water Valve. I then had to unplug the unit from the electrical connectors. After that I had to cut the plastic hoses off the valve. All that was left was to reconnect everything, replace the cardboard covering and do an operational test. Everything worked. The ice maker began to produce ice cubes and there were no leaks.

broken light switch

  • Customer: Francis from Holmes, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Popped out the old one and put in the new one it took five minutes.

would not "dump" ice cubes

  • Customer: Phayo from Lake Charles, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

summer cottage lost heat during winter inlet valve for icemaker froze

  • Customer: Robert from Waterford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>

My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.

  • Customer: Steve from Canyon Country, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.

Ice maker leeking

  • Customer: Wes from Marion, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
opened back panel and replaced valve verry easy

Both cams (upper and lower) broken

  • Customer: Louis from Cortland, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The part came within 3 days. But it was only one cam. Part was described assembly so i thought it had both cams. I ordered the upper cam which attached to the door bottom. When I matched the new to the old --they were different. They looked the same until you put them side by side. Being the mechanic I am, I cut the rivet holding the assembly cam and pop riveted it to the old assembly. It was not difficult but annoying as I had the correct model (I have the original use and care guide book). I must commend PartSelect for their promptness.

The auger in the ice bucket was rusted

  • Customer: Frank from Temecula, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .

Put the part in and observed water leaking from the ice maker which caused the cup to break

  • Customer: John from Ravenden, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered new Ice Maker from you and fixed the problem completely.

no ice

  • Customer: Richard from Las Cruces, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the video, very simple

Drawer Slide Rail cracked/broken

  • Customer: William from Bossier City, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video supplied by manufacturer and followed the instructions. Very easy.

Not dispensing water

  • Customer: Anthony from Orlando, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I watched the video on the partselect website once and completed the repair. Very easy!

the old slide broke

  • Customer: darlene from phoenix, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
when I got on your site I was able to find the part easily & your installation video was a big help. It fit perfectly & was very easy to install--it's working great!!!!!thank you so much
All Instructions for the CSC27HRAAD
481-495 of 509