Models > CSC24DRAAD > Instructions

CSC24DRAAD Hotpoint Refrigerator - Instructions

All installation instructions for CSC24DRAAD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC24DRAAD
691-705 of 733
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker stopped making ice.

  • Customer: Charles from Edmond OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Was not making ice cubes

  • Customer: Bob from JASPER GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

ice maker very slow and arm that controls amount of ice sticking and quit making ice

  • Customer: Grimes from Bartlett TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

Bad switch for door prevented interior light from coming on

  • Customer: Patricia from Sylva NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Self closing upper and lower cam had broken

  • Customer: Charles from Metropolis IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

Door would not close.

  • Customer: Daniel from Cherry Hill NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
With my wife's help, we emptied the door shelves and removed the door to the kitchen table. The video and instructions for replacing the parts were 100% right. We probably spent more time cleaning the door bottom and gasket than actually changing the hinge assembly! The job went very smoothly and saved us from overspending on a repair to this old fridge, or worse, making a quick decision on buying a new one.

Refrigeratior door of side by side would not close

  • Customer: Alison from Lincolnton NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!

Broken Bottom Hinge

  • Customer: William from MIDDLE POINT OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

Refridgerator door was not closing properly

  • Customer: Tim from New Berlin WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the u tube video that was on the Part select website. Very easy install when following the video.

The refrigerator door would not close on its own because the cam was wore out.

  • Customer: ANTONIO from LUTHERVILLE MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I just followed the video instruction supplied by PartSelect and the whole thing was a breeze.

Freezer door hinge.

  • Customer: Mitchel from Onley VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.

DOOR WASN'T CLOSING ALL THE WAY.

  • Customer: John from Valdosta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
DID THE REPAIR JUT LIKE THE INSTRUCTIONS ON THE WEB SITE STATED. THERE WAS A GOOD VIDEO FOR DOING THIS REPAIR. LOOKED AT IT A COUPLE OF TIMES AND DID THE REPAIR RIGHT OFF THE BAT. THANKS FOLKS.

The auger in the ice bucket was rusted

  • Customer: Frank from Temecula CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .

My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.

  • Customer: Steve from Canyon Country CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
All Instructions for the CSC24DRAAD
691-705 of 733