Models > CSC22GRSBAD > Instructions

CSC22GRSBAD Hotpoint Refrigerator - Instructions

All installation instructions for CSC22GRSBAD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC22GRSBAD
676-690 of 823
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

bad driver cup and auger.

  • Customer: Milton from Willingboro NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced the ice buck, not difficult at all thanks for having it.

Replaced ice bucket assembly

  • Customer: Elizabeth from Melbourne FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old ice bucket assembly and used a screwdriver to remove the front panel (4 screws ) and installed it on the new ice bucket assembly, this took only a couple minutes and I inserted the part back into the freezer and that was it. By the way, I'm a 70 year old female.

The drive cup was old,worn,slipping and appeared to have never reached deep enough.

  • Customer: Frank from Villa Rica GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the front of the unit assembly and removed the entire auger unit and drive assembly. I married the old drive cup and new drive cup back to back using vise grip pliers, drilled 4 3mm holes, installed 4 phillips head stainless steel screws and, using an emory wheel, ground off the exposed screw ends. I then re-installed the drive assembly and auger unit. This increased the length of the drive cup allowing the drive to fit without any slippage. The entire cost was less than $18.00 including shipping and screws and took about 1 hour. It works great.

plastic in ice

  • Customer: Donald from Maitland FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
remove 3 bucket screws. 1 bracket screw slide bucket back insert drive reverseb steps

the cam broke because of weight and age

  • Customer: james from tryon NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video on the webpage and did as he did. it was quick and easy. didn't realize the importance of this little part until it broke

door would;ent close tight

  • Customer: Terry from Port Angeles WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced door closing bottom cam

Door cam broke

  • Customer: Robert from yorkville IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the instruction video. The price was high for a plastic part the size of a quarter.

The door closing cam disintegrated and had to lift door to close it

  • Customer: Philip from Charlottesville VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ther was a video on how to repalce this part on your web site. Describing what tools were needed saved me running back and forth to my tool box. I followed the directions given in the video and repair was completed in 1/2 hour. That included meremoving then cleaning and replacing the sheves in the door. And by the way, the part was shipped the same day I ordered it and arrived on my doorstep noon the following day.

Strange noise when opening/closing right side door

  • Customer: Benjamin from Plano TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your video a couple of times, just to be sure I had the sequence down pat. The repair followed the video exactly and was completed in about 12-minutes. I was a bit leary whether I would be able to handle the door weight and alignment but it all went into place without any problems.

Door closing cams broken

  • Customer: Daniel from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
This job would have gone a lot faster if my father, Daniel Stewart would have let me replace it. He has trouble seeing and moves very slow. However, I have learned to be very, very patient. LOL!! One thing, I only ordered 1 because we thought that was all that was needed. It required two. Both were worn out. I do not have the model number off hand, it is a side by side, 16 years old.

broken cam riser on the bottom of the door

  • Customer: Charles from Anaheim CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the refrigerator on again!

Door didn't shut cleaning, by itself

  • Customer: Jim from Wheaton IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video online, and said, "hey, I can do that." And yep, I did. I'm pretty comfortable with handyman work - but had never tackled a frig door before. The door closing cam that had completely come apart turned out to be straight forward to fix with the replacement part.

Fridge cam broke, door barely closed and crooked

  • Customer: Charles from RIO RANCHO NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

Refrigerator door would not close completely.

  • Customer: Ronald from Reno NV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.

Freezer door would not close properly

  • Customer: Lynne from Toledo OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.
All Instructions for the CSC22GRSBAD
676-690 of 823