Models > CSC20GWSBAD > Instructions

CSC20GWSBAD Hotpoint Refrigerator - Instructions

All installation instructions for CSC20GWSBAD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC20GWSBAD
781-795 of 851
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

Water on floor, ice on bottom of freezer, won't dispense water

  • Customer: Jerry from Mission Viejo CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Problems were due to the solenoids for the inlet valves not turning on and off as quickly as they should. Unplugged the refrigerator and pulled it out from the wall to get access to the back. Removed the back cover and the screw that holds the dual water inlet assembly, just as shown in the video. One difference is that the connectors for one of the new solenoids are narrower than the originals. It is necessary to use the two little adapter blades provided along with the new assembly to make them fit tightly in the existing wiring harness connector. We also noticed that the ice dispenser flapper was not closing all the way. Removed the trim plate around the water/ice dispenser by slipping a knife blade under the bottom edge and prying it loose. It was not as easy as in the video. Next, removed the nameplate and 4 screws that are under it. Disconnected the wiring plug at the top left and let the disconnected front assembly hang down to get access to the ice dispenser door solenoid. Disconnected the wiring harness from the solenoid and removed the solenoid attaching screws. Removed the flapper and it's crank arm and then the spring. Put everything back together in reverse order. The only thing a little bit tricky is that the trim plate must be hung from the top cleat first before pressing the sides and bottom edges to snap them back in place. Very nice to have water, ice, and a dry floor again.

Ice maker not making ice

  • Customer: david from raleigh NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I'm a real novice at appliance repair but learned a lot from this effort. After doing enough online research and watching videos, I diagnosed the problem with my 20 year old ice maker. It was working, just not getting water. So I ordered a new water valve, much cheaper than the part Sears recommended. I easily hooked up the new valve but the old copper water supply line was leaking so I ordered a $7 pex line from Home Depot. Hooked it all back up and now I'm in business, and saved some money too!

water was dripping from this valve

  • Customer: Michael from Bryan TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the valve from the fridge with a nut driver, this allowed me to disconnect the two lines and the water main inlet. Re attach the main line and cut off ends of both plastic lines with a razor knife and re insert the two lines. Last was to connect the main water inlet and tighten . The last thing was to turn on the water and check for leaks and we had none so put the fridge back in its proper place and job done. Thank you for your help Michael

Water wouldn't stop running out of tube on door

  • Customer: Jon from Land O Lakes FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was really easy, bought the part because of partselect video. Saved myself a lot of money vs calling a repairman.

water leaking from cube former

  • Customer: Lee from Deltona FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
turned water off removed old water valve moved wires to new one moved water supply and discharges to new one reinstalled new valve

ice maker did not work

  • Customer: Michael Welbourne from Battle Creek MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Got a new valve

Water leaking form Duel Inlet valve

  • Customer: Michael from Colonia NJ
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I noticed water leaking from the bottom right rear of the fridge. I figured it was from the ice maker feed as I don't have the ice water feature on this GE profile. I shut the water supply off, ordered the part and received it in a few days. The defective part was easily accessible after I removed the cardboard cover. I removed the copper feed and unscrewed the old valve with a nutdriver. The new part fit perfectly, and even though there were instructions in the part to use the old bracket. the plastic water feed fit into the ice maker compression fitting with ease. I ran into a problem when I re-installed the copper compression fitting on the new valve,as I could not stop a leak from the top of the compression fitting. When my plumber originally installed the copper line he used enough pressure to deform the compression sleeve that slips over the copper tube. I had a couple of them in my "parts" drawer, so I took my tubing cutter and took 1/2" of the end of the copper supply line; slipped the new sleeve and re-installed the compression nut over the valve....fit perfectly. Turned on the water supply; no leaks. Checked the icemaker about 4 hours later and it made the first tray of ice. If I didn't have to deal with the water supply leak at the fitting, the job would have been finished in 30 to 45 minutes.

water side not working

  • Customer: Marie from Winter Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
pulled out frig unplugged power turned off water at tank disconnected water line and electrical plugs replaced valve replaced wire hook ups different size but easy to install.(came with valve) Cut water lines off inserted into valve different sizes so easy to connect in right place. Reattached electrical wires. (Note remember were the wires came from) Checked for leaks Done! Might want to make sure tubes are inserted completely and you cut the tubes off straight...possible water leak if not.

water dispenser in door leaking

  • Customer: Kevin from Sunrise FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove the back cover where the valve is located, unplug the refrige, turn the water off. Remove the valve unit, cut the plastic water lines with the utility knife,unscrew the water feed. remove the unit. reasemble the new unit,install the water feed, connect by puching in the ice maker line and the water despencer line into the new unit.Plug the refrig back in and purge the water line. (done) saved a service call$$$$

The ice maker did not make any ice cubes

  • Customer: Robert Mc from Citrus Heights CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I pulled the Refrig out of the space so that I could get to the plug and water shut off. After unplugging and turning the water off, I had to remove the 7 screws holding the cardboard cover over the bottom portion of the Refrig. I then had to unloosen the water input to the the valve. Then I removed the screw holding the Water Valve. I then had to unplug the unit from the electrical connectors. After that I had to cut the plastic hoses off the valve. All that was left was to reconnect everything, replace the cardboard covering and do an operational test. Everything worked. The ice maker began to produce ice cubes and there were no leaks.

KEPT WIPING UP WATER ON FLOOR TRIED DE-ICING WITH NO LUCK !

  • Customer: Thomas from Centerville OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
TOOK BACK OFF WITH SOCKETS AND SAW WATER DRIPPING FROM DUEL INLET WATER VALVE . TURNED WATER OFF AND HAD NO TROUBLE INDENTIFYING PART WITH PartSelect VIA COMPUTER , ORDERED PART USING UPS AND RECEIVED IN TWO DAYS , FOLLOWED AN EXCELENT VIDEO FURNISHED BY PartSelect THEN REPLACED NEW PART WITH OLD PART , TURNED WATER BACK ON AND GREAT ! I FOUND IT A LOT EASYIER WHEN YOU HAVE YOUR SON-IN-LAW DO THE WORK !

water manifold cracked

  • Customer: Jason from Littleton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I used the how to video from the site and had the part replaced in about the same time the video did it, even with being distracted with a phone call.

Ice maker not working

  • Customer: Patricia from Palmdale CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I have never repaired anything before but I found your web site ordered the item and received it in 2 days Thank You,thank you

summer cottage lost heat during winter inlet valve for icemaker froze

  • Customer: Robert from Waterford CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>
All Instructions for the CSC20GWSBAD
781-795 of 851