CSB2323ARW Magic Chef Refrigerator - Instructions

After reading the articles previous owners wrote, I tackled the repair. There were no big problems until I had to change out the water line on the icemaker tray--that part was for a different frig--so it had to be changed out with the Amana water line part that was enclosed. I couldn't get that part removed, so I had to have my husband change it out. He then finished the installation. Everything went smoothly, just my pride wanted me to finish it all by myself.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

got the model number off the fridge. ordered the part. received the part. the funnel part that drains the water into the tray was broke when I received the new icemaker, I took the one that was on my old leaking icemaker an put it on my new one along with the old hardware parts {wireharness, ice level bar}. followed the video instructions an wahlah nomore ice in the bottom of the freezer or in the floor. it looked like the funnel was broke in shipping. its great to have ice because its fixing to get hot!

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.

Remove rear panel with 1/4 nut driver. Pop plastic cover on compressor. Pry off relay and two wires and reinstall. Nice and easy and back to full function :)

removed the old ice maker and put in the replacement one we purchased.

easy enough, removed 3 screws, unplugged wiring harness, put new unit on work bench, put old wire harness on new unit, put old motor cover on new unit,(the only trouble i had was figuring out how to swap the light blue plastic piece for the white plastic piece, i just put a screwdriver underneath and applied pressure) plugged harness back into freezer, turned water back on and waited... 2 hours later heard beautiful ice cubes dropping into tray :)

The ice maker was easy but the older Maytag inlet valves are rigid plastic line- make sure that line is properly connected to back of fridge- the 1st night the water leaked down back of freeze- thus no ice in ice maker tray ----but the bottom of freezer was full of frozen water--- took ice maker off and realigned inlet pipe- once that was done- no more problems- ( did also have to take hair dryer and remove all ice build up in bottom of freezer --- remember to check that rigid line as it can become detached while changing out ice maker assembly- thx Greg

Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.