Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CRTR9300AS0

CRTR9300AS0 Frigidaire Washer - Overview

Get Parts and Repair Help for CRTR9300AS0

If you know the washer repair part you need, you can browse the list of all parts on the CRTR9300AS0, or you can search by name or part description. You can also find your part by where it is located on the CRTR9300AS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for CRTR9300AS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.63

Selector Knob

This selector knob may also be known as the laundry appliance control knob and is meant for your washer or dryer. This model is sold individually and takes a D-shaped shaft. The pu...

$8.86

Door Strike

The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks, or the washer will not start or spin, you may need to replace the door strike. This part is for front load washers. The part is made of plastic and is roughly 2 inches in length. To complete this repair, you will only need a Phillips screwdriver. Most of our customers found this repair to be easy, and took less than 15 minutes to complete it.

$76.25

Door Lock and Switch Assembly

This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock ...

$45.88

Shock Absorber Kit

This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

$103.78

Drain Pump - 60Hz 120V

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$31.31

Single Spring with Insulators

This is a single spring with insulator, but you may also know it as a suspension spring. It is a part for your washing machine. If your tub is no longer stable, which would cause s...

$6.36

SCREW

$15.49

Drive Belt - 6 ribs

This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive be...

$6.67

SCREW

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Door Catch

  • Customer: Joy from Columbia, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 516 of 517 people found this instruction helpful
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done. read more

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 392 of 461 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. read more

Both vibration shock absorbers broken

  • Customer: Douglas from Medical Lake, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 155 of 163 people found this instruction helpful
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went w... read more